Paradyne COMSPHERE 3800 Series User Manual Download

Page: 147 / 213

COMSPHERE 3800 Series Modems

14-6

September 1998

3810-A2-GB30-30

Table 14-1

(4 of 12)

3800 Series AT Commands

Command

Front Panel

Branch

Description

Tone Dial
Sets the modem for tone dial mode.

Configure\Edit\Line
Dialer

Result Code Format
V0

Displays result codes in Number (1) format digits.

Displays result codes as text.

Displays result codes in Number (2) format (digits).

Configure\Edit\DTE
Dialer

Extended Result Code, Dial Tone Detect, and Busy Tone Detect
Configuration Options

Ext Dial Tone Busy Tone

Result Code Detect Detect

Disable

Enable

Disable

Enable Enable

Disable

Enable

Disable

Enable

Enable Enable

Enable

Add/EC

Enable Enable

Add/V42,MNP

Enable Enable

Use DTE Rate

Enable

Extended Result Code:
Configure\Edit\DTE
Dialer

Dial Tone Detect:
Configure\Edit\Line
Dialer

Busy Tone Detect:
Configure\Edit\Line
Dialer

Use DTE Rate

Enable

EXTENDED RESULT CODE

Enable. Displays all result codes listed in Table B-1 except for error control
suffix.

Disable. Only displays OK, CONNECT, RING, NO CARRIER, ERROR.

Add/EC. Displays result codes with /EC suffix. Add/V42,MNP. Displays result
codes with either V.42 or MNP suffix. Use DTE Rate. Displays DTE data rate
instead of line rate.

Add/V42,MNP. Displays result codes with either V.42 or MNP suffix.

Use DTE Rate. Displays DTE data rate instead of line rate.

DIAL TONE DETECT

Enable. Sets the modem for dial tone detect.

Disable. Sets the modem for blind dialing.

BUSY TONE DETECT

Enable. Modem monitors for busy tone.

Disable. Modem ignores busy tone.

Long Space Disconnect
Y0

Disable. Ignores long space.

Enable. Disconnects if long space is detected. Enables transmission of a
long space.

Configure\Edit\Line
Dialer

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands

Paradyne COMSPHERE 3800 Series, User Manual

Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands