Paradyne COMSPHERE 3800 Series User Manual Download

Page: 150 / 213

AT Command Set and S-Registers

14-9

3810-A2-GB30-30

September 1998

Table 14-1

(7 of 12)

3800 Series AT Commands

Command

Front Panel

Branch

Description

Dial Transmit Level

When Dial Transmit Level Type is set to Permissive, &

sets Dial Transmit

Level to a value between –10 and –32 dBm. &

99 and &

100 cause the level to

be varied automatically according to conditions for Enhanced Throughput
Cellular (ETC) operation, and are valid only if ETC is installed.

10 –10 dBm

–11 dBm

32 –32 dBm

99 Automatically adjusted according to the ETC1.0 specification

Use only

with remote modems set to &

99, and limit the data rate to 4800 bps

(S41 = 5). Set by &F6.

100 Automatically adjusted according to the ETC1.1 specification.

NOTE: &J0 overrides this command; &

n overrides the &J0 command.

Configure\Edit\Dial Line

&Jn

Dial Transmit Level Type

&J0

Permissive (Approx. – 9 dBm).

NOTE: &Jn overrides the &

n command.

Configure\Edit\Dial Line

&Ln

Leased Mode

&L0

Disables leased-line operation.

&L1

2-wire originate leased-line operation.

&L2

4-wire originate leased-line operation (Model 3810 and 3811 only).

&L3

2-wire answer leased-line operation.

&L4

4-wire answer leased-line operation (Model 3810 and 3811 only).

The &L command will cause the modem to reset before entering or exiting
Leased-Line mode. Therefore, it must be entered as the last command in an
initialization string.

Configure\Edit\Leased
Line

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands

Paradyne COMSPHERE 3800 Series, User Manual

Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands