Paradyne COMSPHERE 3800 Series User Manual Download

Page: 46 / 213

DCP Operation

4-15

3810-A2-GB30-30

September 1998

Diagnostic Control Panel
Security Access

NOTE

This page of the manual is
self-supporting and can be
removed to prevent unwanted
knowledge of the DCP security
access selections.

Use the DCP security access function to ‘‘lock” the

DCP of any 3800 Series modem and prevent unwanted
user access. Two options are available for this function:
Grant and Deny.

Grant allows any branch of the Top-Level menu to be

accessed from the DCP. Deny allows access only to the
Status branch of the Top-Level menu. All 3800 Series
modems are shipped from the factory with DCP access
granted.

To access the Front Panel (DCP) Security Access

function, perform the following:

Press the

key three times.

Press the

key twice.

Press the

key once.

Frnt Panl Acces
Grant Deny

Select Grant to allow access or select Deny to lock

DCP access.

Either selection results in a return to the Top-Level

menu.

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands

Paradyne COMSPHERE 3800 Series, User Manual

Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands