manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, User Manual

The Paradyne COMSPHERE 3800 Series offers advanced telecommunications solutions. Stay up-to-date with the latest features and enhancements through our free Firmware Update. Download the comprehensive manual from manualshive.com to maximize your usage and unlock the full potential of this cutting-edge product.

Share
Download
background image

Configure Branch

9-41

3810-A2-GB30-30

September 1998

Misc

The Miscellaneous configuration options determine

specifics for various functions, including network
management parameters and remote modem access. 

Table 9-8 shows each Misc (Miscellaneous)

configuration option as it appears on the LCD, with the
Async Dial factory default setting (the default value if the
modem is just being installed) shown following the 
colon (:) on the first line and with all available selections
listed on the second line. Following this is a description of
the configuration option, a description of the available
selections, and any equivalent AT commands.

Table 9-8

(1 of 4)

Miscellaneous Configuration Options

StrapsWhenDisc: No_Change
Nxt

No_Change

Reload   RelodNoATChg

Straps When Disconnected. Determines whether or not configuration options in the Active (Saved) configuration area
are reloaded to Active (Operating) when a disconnect occurs. This is useful in modem pooling applications.

No Change – Configuration options do not change upon disconnect.

Reload – The Active (Operating) configuration area, which controls modem operation, is reloaded from the Active
(Saved) configuration area when a disconnect occurs. This is useful in modem pooling applications where it is desirable
to start the modem from a known condition after every call. This allows multiple users to issue AT commands to change
the modem’s operation for their particular call.

Reload, No AT Change – This has the same effect as Reload, except that it becomes impossible to change this
configuration option with an AT command, and the command buffer is cleared so that AT\A (Repeat Last Command) has
no effect.

NOTE:  If Reload or RelodNoATChg is selected, the following AT commands are disabled although the OK result code

appears when these commands are issued: 

AT&F0. Loads Async Dial into Active(Operating) 
AT&F1. Loads Sync Dial into Active (Operating) 
AT&F2. Loads Sync Leased (Answer) into Active (Operating) 
AT&F3. Loads UNIX Dial into Active(Operating) 
AT&F4. Loads Sync Leased (Originate) into Active (Operating) 
AT&F5. Loads Cellular(Mobile) into Active (Operating)
AT&F6. Loads Cellular (PSTN) into Active (Operating)
AT&W0. Write Active(Operating) to Active(Saved) 
AT&W1. Write Active(Operating) to Customer 1 
AT&W2. Write Active(Operating) to Customer 2 
AT&Zn=x. Store directory numbers

The factory default is No_Change.

AT command for No_Change is S88 = 0 or S88 = 231. 
AT command for Reload is S88 = 1 or S88 = 232. 
AT command for Reload with no AT Change is S88 = 2 or S88 = 233.

Speaker Control: OnUntilCarr
NxtOn

UntilCarr

Off

On

Speaker Control. Determines if the speaker is Off, On until carrier signal is received by the modem, or On all the time.

The factory default is OnUntilCarr.

NOTE:  Speaker Control can also be temporarily set using the Control branch; however, a reset or power cycle will

restore the modem to the Speaker Control and Speaker Volume configuration option settings.

AT command for Off is M0 AT command for On Until CD is M1. 
AT command for On is M2.

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3800 Series

PROLiNK 1456PVA User Manual preview
1456PVA
Brand: PROLiNK Pages: 10
Patton OnSite 3088A/I User Manual preview
OnSite 3088A/I
Brand: Patton Pages: 57
Draytek Vigor120 Series Quick Start Manual preview
Vigor120 Series
Brand: Draytek Pages: 8
Teracom T2-B-Gawv1.4U10Y-BI User Manual preview
T2-B-Gawv1.4U10Y-BI
Brand: Teracom Pages: 131
Zhone 6381-A3-xxx Specification preview
6381-A3-xxx
Brand: Zhone Pages: 2
Paradyne COMSPHERE 3810Plus Quick Reference preview
COMSPHERE 3810Plus
Brand: Paradyne Pages: 28
ELSYS.se ELT Lite Operating Manual preview
ELT Lite
Brand: ELSYS.se Pages: 19
NETGEAR DG834Gv3 - 54 Mbps Wireless ADSL Firewall Modem Setup Manual preview
DG834Gv3 - 54 Mbps Wireless ADSL Firewall Modem
Brand: NETGEAR Pages: 32
Swarm Tile Product Manual preview
Tile
Brand: Swarm Pages: 63
Gigalink SU-400 User Manual preview
SU-400
Brand: Gigalink Pages: 6
Ubee DDM3521 User Manual preview
DDM3521
Brand: Ubee Pages: 29
HORNER HE-XRZ2 Quick Start Manual preview
HE-XRZ2
Brand: HORNER Pages: 11
Gnet BB0050 Configuration And Installation Manual preview
BB0050
Brand: Gnet Pages: 55
Atal ATXV-AC05-GPRS Manual preview
ATXV-AC05-GPRS
Brand: Atal Pages: 39
Radicom Research RW8300E-a-PR Designer'S Manual preview
RW8300E-a-PR
Brand: Radicom Research Pages: 48
Vega Absolute NB-12 User Manual preview
NB-12
Brand: Vega Absolute Pages: 26
Patton OnSite 3088A Quick Start Manual preview
OnSite 3088A
Brand: Patton Pages: 8
Cermetek iModem CH2156 Manual preview
iModem CH2156
Brand: Cermetek Pages: 19

Brands by name

Popular brands

Load more brands