Paradyne COMSPHERE 3800 Series User Manual Download | Manualshive

Page: 148 / 213

background image

AT Command Set and S-Registers

14-7

3810-A2-GB30-30

September 1998

Table 14-1

(5 of 12)

3800 Series AT Commands

AT

Command

Front Panel

Branch

Description

Zn

Reset and Load Active
Z0

Loads configuration options from Active (Saved) to Active (Operating).

Z1

Loads configuration options from Customer 1 to Active (Operating).

Z2

Loads configuration from Customer 2 to Active (Operating).

Z3

Loads configuration options from Active (Saved) to Active (Operating)
and performs a “soft” reset (if the modem is connected, it is
disconnected).

Z9

Performs a full modem reset, as if the power were turned off and on.

Control\Reset

&Cn

LSD Control
&C0

Forced On. LSD on at all times.

&C1 Standard RS232. LSD is on when the remote modem’s carrier signal is

detected. LSD is off when carrier signal is not detected.

&C2

Wink When Disconnect. LSD normally forced ON, turns Off for
approximately one second upon disconnecting.

&C3

Follows DTR. State of LSD follows state of DTR.

&C4

Simulated Control Carrier. State of LSD follows state of remote modem’s
RTS.

&C5

=DTR/Disconnect Off. State of LSD follows state of DTR except upon a
disconnect where DTR remains ON and LSD turns Off. DTR must then
toggle Off and ON to turn LSD ON. Use this setting for AT&T DATAKIT
applications. Note that to use this option, the DTR Action configuration
option must be set to Stndrd_RS232 (&D1 or &D2).

&C6

Bridge Retrain. LSD behaves as if it were set for Stndrd_RS232, except
that it is turned off when a retrain condition lasts longer than 10 seconds,
and turned on again when no retrain condition is detected for a period of
10 seconds.

Configure\Edit\DTE
Interface

&Dn

DTR Action
&D0

Ignore. Modem ignores the true status of DTR and treats it as always
ON.

&D1

Off=Command Mode. Modem enters online Command Mode if
connected when DTR switches Off.

&D2

Standard RS232. DTR Signal is controlled by the DTE.

&D3

Off=Reload Strap. Follows Standard RS232 operation, except that when
DTR switches Off, the modem loads the Active (Saved) area into the
Active (Operating) area.

&D4

Controls On-Hook. Follows Standard RS232 operation, except that
modem does not disconnect until DTR is lowered by the DTE.

&D5

Controls TX Mute. Follows Standard RS232 operation, except that when
DTR is lowered at the answering modem, the modem mutes transmitter
output.

Configure\Edit\DTE
Interface

«
...
146
147
148
149
150
...
»

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3800 Series

Brand: Creative Pages: 57

Brand: Asus Pages: 4

Brand: Asus Pages: 47

Brand: Asus Pages: 173

DIVA T/A ISDN Modem

Brand: Eicon Networks Pages: 146

Brand: Belkin Pages: 2

Brand: Zoom Pages: 2

Brand: Zoom Pages: 40

Brand: Four-Faith Pages: 34

Brand: O2 Pages: 48

Brand: Hughes Pages: 126

Brand: Hughes Pages: 68

Brand: TRENDnet Pages: 91

Brand: US Robotics Pages: 192

MOD 9001C RS232

Brand: Sky Microwave Pages: 13

Brand: Atal Pages: 39

Brand: Raveon Technologies Corporation Pages: 9

Brand: Paradyne Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands