manualshive.com logo in svg

Paradyne COMSPHERE 3800 Series, User Manual

The Paradyne COMSPHERE 3800 Series offers advanced telecommunications solutions. Stay up-to-date with the latest features and enhancements through our free Firmware Update. Download the comprehensive manual from manualshive.com to maximize your usage and unlock the full potential of this cutting-edge product.

Share
Download
background image

Configure Branch

9-23

3810-A2-GB30-30

September 1998

Table 9-3

(4 of 5)

Line Dialer Configuration Options

No Carrier Disc: 2sec
Nxt

2sec

5sec

Disable

10sec

20sec

No Carrier Disconnect. If the modem no longer receives carrier from the remote modem, it disconnects the call. This
configuration option determines how long carrier is Off before the modem disconnects. Loss of carrier is one method of
disconnecting a call.

2, 5, 10, 20 sec – Modem disconnects if carrier turns Off for more than 2 seconds, 5 seconds, 10 seconds, or 
20 seconds.

Disable – Modem does not disconnect if carrier turns Off.

The factory default is 2sec.

AT command is S-register S10 = n, where n is 255 for disable or 0 to 254 in 0.1 second increments for enable.

No Data Disc: Disable
Nxt

Disable

10min

30min

60min

No Data Disconnect. Forces the modem to disconnect if no data is transmitted or received within a specified amount of
time.

Disable – Modem remains connected despite the lack of data flow.

10, 30, 60 min – Modem disconnects if data is not received or transmitted within 10-minute, 30-minute, or 60-minute
intervals.

The factory default is Disable. The reloading of factory defaults does not affect No Data Disconnect.

AT command to enable is \Tn, where n is a value from 1 minute to 255 minutes. AT command to disable is \T0.

NoDataDiscTrig
Nxt

TXD or RXD   TXD and RXD   TXD Only   RXD Only

No Data Disconnect Trigger Signal. Works in conjunction with No Data Disconnect (\T), and determines whether Pin 2
(transmit data) or Pin 3 (receive data) of the modem’s RS-232 serial interface is monitored so that the modem can
disconnect the call if there is no activity for a certain period of time.

The No Data Disconnect Trigger Signal configuration option is unavailable and is not displayed on the DCP when No
Data Disconnect is disabled. The factory default is TXD or RXD. The reloading of factory defaults does not affect No
Data Disconnect Trigger Signal.

TXD or RXD – Disconnect if no data transmitted or received for specified period.

TXD and RXD – Disconnect if no data transmitted and received for specified period.

TXD Only – Disconnect if no data transmitted for specified period.

RXD Only – Disconnect if no data received for specified period.

AT command is S80 = n:

S80 = 0 Transmit or Receive
S80 = 1 Transmit Only
S80 = 2 Receive Only
S80 = 3 Transmit and Receive

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Reviews:

No comments

Related manuals for COMSPHERE 3800 Series

T-Mobile SONIC User Manual preview
SONIC
Brand: T-Mobile Pages: 10
Paradyne HotWire 7914 User Manual preview
HotWire 7914
Brand: Paradyne Pages: 60
jablotron MS-33 Manual preview
MS-33
Brand: jablotron Pages: 4
SAGEMCOM Sunrise Internet Box User Manual preview
Sunrise Internet Box
Brand: SAGEMCOM Pages: 2
BROSTREND WNA016 User Manual preview
WNA016
Brand: BROSTREND Pages: 13
Zte MF335 User Manual preview
MF335
Brand: Zte Pages: 36
Maxon MA-2020 User Manual preview
MA-2020
Brand: Maxon Pages: 100
Kasda KW 58283 User Manual preview
KW 58283
Brand: Kasda Pages: 40
Kasda KW5863 User Manual preview
KW5863
Brand: Kasda Pages: 41
Enfora GPRS User Manual preview
GPRS
Brand: Enfora Pages: 23
iBall Airway 14.4GW-01 User Manual preview
14.4GW-01
Brand: iBall Airway Pages: 2
X-Micro XBT-AM2 User Manual preview
XBT-AM2
Brand: X-Micro Pages: 22
Hughes PES 5000 Manual preview
PES 5000
Brand: Hughes Pages: 17
3Jtech uModem Technical Document preview
uModem
Brand: 3Jtech Pages: 50
NETGEAR DM602 - ADSL-Modem - 8 Mbps DSL Modem Reference Manual preview
DM602 - ADSL-Modem - 8 Mbps DSL Modem
Brand: NETGEAR Pages: 66
Milltronics VT-Modem-1 WW Instruction Manual preview
VT-Modem-1 WW
Brand: Milltronics Pages: 24
Hamlet HDSL640 User Manual preview
HDSL640
Brand: Hamlet Pages: 37
Raveon RV-SMB Technical Manual preview
RV-SMB
Brand: Raveon Pages: 13

Brands by name

Popular brands

Load more brands