Paradyne COMSPHERE 3800 Series User Manual Download

Page: 146 / 213

AT Command Set and S-Registers

14-5

3810-A2-GB30-30

September 1998

Table 14-1

(3 of 12)

3800 Series AT Commands

Command

Front Panel

Branch

Description

Identification

Displays product code; default is 144.

Displays 3-digit firmware revision number.

Performs an EPROM check.

Displays the modem’s serial number.

Displays the modem’s model number.

Displays the part number of the circuit card.

Displays the firmware release number.

Displays 3-digit firmware revision number (same as

1).

10=n Changes the value of the product code displayed by the

0 command; n

is a number from 0 to 4:

10 = 0 sets product code to 144

10 = 1 sets product code to 240

10 = 2 sets product code to 480

10 = 3 sets product code to 960

10 = 4 sets product code to 120

Performs a checksum of the modem’s firmware and displays the results
in hexadecimal. (There is no DCP equivalent of this command.)

Displays the last sequence fault record.

Displays the entire firmware revision level.

Status\Identity

Speaker Volume
L0

Selects low volume.

Selects medium volume

Selects high volume.

Control\Speaker

Configure\Edit\Misc

Speaker On/Off
M0

Speaker always off.

Speaker on until carrier signal is detected.

Speaker always on.

Control\Speaker

Configure\Edit\Misc

Return to Online or Data Mode
Returns modem to Data mode from Online Command mode.

None

Pulse Dial
Sets the modem for pulse dial mode.

Configure\Edit\Line
Dialer

Result Codes
Q0

Enables modem to send result codes to the DTE.

Disables modem from sending result codes to the DTE.

Enables in Originate mode only for modem to send result codes to the
DTE. Required for most UNIX applications.

Configure\Edit\DTE
Dialer

Sr =n

Change S-Register
Changes contents of S-register (where r is the S-register, and n is the new
value).

None

Sr ?

Display S-Register
Displays value of S-register where r is the S-register number.

None

Summary of Contents for COMSPHERE 3800 Series






















































































































































































































Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands

Paradyne COMSPHERE 3800 Series, User Manual

Search results

Summary of Contents for COMSPHERE 3800 Series

Reviews:

Related manuals for COMSPHERE 3800 Series

Brands by name

Popular brands