8
8
1. Receiver
Receives the signal sent from the
remote control.
2. Emergency
operation
button
Display lamps
When an error occurs, one of the
lamps flashes. When a display
lamp is blinking, refer to " Before
Requesting Service ".
3.
This lamp is lit when the unit is
operating.
4.
This lamp is lit when the timer is
set.
5.
Operating lamp
Timer lamp
Standby lamp
•
When the heater is working,
the lamp lights at the following
times. When the thermostat has
operated during defrosting at the
time of the startup.
•
The lamp flashes when an error
occurs.
6.
This lamp is for notifying you when
the filter needs to be cleaned.
7.
Filter lamp
Swing button
8. Normal/Stop
All switch
Use in the
Normal
position. It
does not operate in the
Stop All
position.
Remote control, main / remote
control, secondary, switch
In normal use this should be on
remote control, main. It is also
possible to use both in conjunction
with a wired remote control (sold
separately). (Consult with the
dealer where the product was
purchased about making the
settings.)
Test/On switch
This is used during service. It is
not for normal use.
Test Run/On switch
This is used during service. It is
not for normal use.
9. Address switch
Differentiate between incoming
and outgoing signals.
NOTE
•
If a heat pump model is being used, it will beep twice and the operating lamp will light up on the display;
if the timer and standby lamps blink alternately, a confict between the heating and cooling exists, so the
unit cannot operate in the desired mode.
(On models that do not have an Auto function, even if Auto is selected, it works in the same way.)
• W
hen the local operation is disabled by such as the centralized control, and if the Start, Stop, Mode or
Temperature setting buttons are pressed, the unit will beep five times and the change will not be made.
RECEIVER
1
2
3
4
5
6
7
8
9
CZ-RWSC2
8-4
SM830194-04_Single_BigPAC.indb 4
2014/10/31 13:30:50
Summary of Contents for S-200PE1E8
