Panasonic KX-TD1232NL Installation Manual Download Page 37

Page: 37 / 183

2.2

Installation of the Main Unit

General Installation

2.2.3

Wall Mounting

This set is designed for wall mounting only. The wall where the main unit is to be mounted
must be able to support the weight of the main unit. If screws other than the ones supplied are
used, use screws with the same diameter as the ones enclosed.

Mounting on Wooden Wall

Place the template (included) on the wall to mark the screw positions.

Install the screws (included) into the wall.

Hook the main unit on the screw heads.

Template

KX-TD816

KX-TD1232

Drive the screw
to this position

Wooden
Wall

KX-TD816

KX-TD1232

Summary of Contents for KX-TD1232NL
























































































































































































Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands

Panasonic KX-TD1232NL, Installation Manual

Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands