Panasonic KX-TD1232NL Installation Manual Download Page 67

Page: 67 / 183

2.4

Installation of Optional Cards and Unit

General Installation

2.4

Installation of Optional Cards and Unit

2.4.1

Location of Optional Cards and Units

The location of the optional cards and units is shown below.

Precaution

To protect the printed circuit boards (P-boards) from static electricity, do not touch parts on the
P-boards in the main unit and on the optional cards.

Expansion Units

KX-TD816

The following expansion units can be installed to any of the two expansion areas.

Panasonic

D816

Expansion

area 2

Expansion

area 1

Expansion Unit
Connectors

Remove the front
cover plate(s).

8-Station Line Unit, KX-TD170:
Adds eight extensions.

4-CO Line Unit, KX-TD180:
Adds four outside lines.

One extension line unit

One outside line unit

Permits access to the system from
outside tone telephones.
A High Speed Remote Card (KX-
TD197) can be installed into this unit.

One DISA Unit, KX-TD190:

Provides data communications between
the system and a remote location.
A DISA Card (KX-TD199) can be
installed into this unit.

One Remote Unit, KX-TD198:

Summary of Contents for KX-TD1232NL
























































































































































































Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands

Panasonic KX-TD1232NL, Installation Manual

Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands