Panasonic KX-TD1232NL Installation Manual Download Page 77

Page: 77 / 183

2.4

Installation of Optional Cards and Unit

General Installation

Note

•

If two expansion units are installed, cut the cabinet cover(s) on the lower cabinet(s) to allow
the cords from upper cabinet to go down through the cabinet cover(s). To protect the cords,
smooth the cut edges.

Amphenol 57JE Type (screw-attach-type 50-pin connector) Connection for KX-TD170

To fix the Amphenol 57JE type (screw-attach type 50-pin connector) to the 8-Station Line Unit,
follow the procedure below.

The 50-pin connector (Jack) on the Expansion Unit has two hook-pins. Remove the upper
hook-pin, and take out the screw.

Note

When installing a connector like the type shown below, unscrew the lower hook-pin also.
Then drive both accessory screws.

Cut here

Screw

50-pin
connector

Hook-pins

Summary of Contents for KX-TD1232NL
























































































































































































Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands

Panasonic KX-TD1232NL, Installation Manual

Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands