Panasonic KX-TD1232NL Installation Manual Download Page 99

Page: 99 / 183

2.4

Installation of Optional Cards and Unit

General Installation

2.4.8

System Connection

To connect two main units, use two optional System Inter Connection Cards (KX-TD192) and
the Connection Cable (included in the cards).

Insert the upper side of the System Inter Connection Card into two hooks on the main unit
(Master System).

Press down the two corners of the lower side of the System Inter Connection Card.

Connect the cord to the System Inter Connection Card connector.

Open the latch on the card.

Repeat steps 1 through 4 for the Slave System, using the other card.

Insert one Connection Cable end into the Master System and insert the other end into the
Slave System.

Available for the KX-TD1232 only.

System Inter Connection Card

Summary of Contents for KX-TD1232NL
























































































































































































Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands

Panasonic KX-TD1232NL, Installation Manual

Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands