Panasonic KX-TD1232NL Installation Manual Download Page 155

Page: 155 / 183

5.2

Wireless System Installation

DECT Installation

155

Insert the modular plug into the Cell Station, and attach the ferrite core (included) to the
plug cord.

Survey the site for the Cell Station by testing the radio signal. Refer to the Section
5.2.5

Site Survey.

Note

•

System Programming is required to assign an extension number to each portable
station. <SYS PRG [650], [671]>

•

For the KX-TD146, an AC adapter (KX-A277) is necessary.
The same AC outlet should be used for the main PBX unit and a Cell Station
Interface Unit.

01 01 01 01 01 01

15 cm

Ferrite Core
Roll the cord once
around the ferrite core
and close the core.

DIGIT

AL SUPER HYBRID SYSTEM

6CS

Wrap the cord once around
the upper hook and pass
through the lower hook.

Summary of Contents for KX-TD1232NL
























































































































































































Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands

Panasonic KX-TD1232NL, Installation Manual

Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands