Panasonic KX-TD1232NL Installation Manual Download Page 122

Page: 122 / 183

3.2

ISDN Line Connection

122

ISDN Installation

Prepare the required plugs. Two 4-pin plugs are included with the KX-TD290.

Insert the plug into a jack on the unit.
Connect a grounding wire to the ground terminal on the extension expansion unit.

Tie all of the cords into a bundle. If other cords are exposed in the upper cabinets, tie them
also.

Close the cabinet cover and secure the outside screw.

If a KX-TD290 is to be installed (KX-TD1232 only):

From Network

To the unit

TB
TA

RB
RA

From Network

To the unit

RB
RA

TB
TA

Panasonic

4
3

View of TEL Jack

DIGIT

L SUPER HYBRID SYSTEM

To Terminal Board or Modular
Jacks from the Central Office

Summary of Contents for KX-TD1232NL
























































































































































































Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands

Panasonic KX-TD1232NL, Installation Manual

Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands