Panasonic KX-TD1232NL Installation Manual Download Page 173

Page: 173 / 183

6.1

Troubleshooting

Troubleshooting

173

6.1.2

Connection

Can you dial
an extension?

The T/R is connected to the D1/D2.

Use the correct cord (inner 2
wires are for T/R and the
outer 2 wires are for D1/D2).

KX-TD816/ extension
KX-TD1232

KX-TD1232 extension

CAUSE

SOLUTION

Use the correct cord (2
second wires from the
outside are for D1/D2 and
the 2 outer wires are for
P1/P2).

*The P1/P2 is connected to the D1/D2.

Yes

T
R

D1
T
R
D2

P1
D1

T
R

D2
P2

P1
D1
T
R
D2
P2

The T/R is connected to the D1/D2.

Connection between the system and a single line telephone:

Connection between the system and a single line telephone that is polarity-
sensitive:

(Continued on the
following.)

Use the correct cord (inner 2
wires are for T/R).

•

If a telephone equipped

with an A-A1 relay is
connected to the system,
set the A-A1 relay switch
of the telephone to "OFF".

KX-TD816/ extension
KX-TD1232

CAUSE

SOLUTION

Connection between the system and a proprietary telephone:

T
R

The "T" is connected to the "R".

Reverse the connections of
the T/R.

KX-TD816/ extension
KX-TD1232

CAUSE

SOLUTION

T
R

*: Available for the KX-TD1232 only.

Summary of Contents for KX-TD1232NL
























































































































































































Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands

Panasonic KX-TD1232NL, Installation Manual

Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands