Panasonic KX-TD1232NL Installation Manual Download Page 157 | Manualshive

Page: 157 / 183

background image

5.2

Wireless System Installation

DECT Installation

157

10.

Cover the cords with the cord holder (included).

11.

Fix the cords to the wall as shown so that the front cover can be opened.

Note

If two expansion units are installed, cut the cabinet cover(s) on the lower cabinet(s) to allow
the cords from the upper cabinet to go down through the cabinet cover(s). To protect the cords,
smooth any cut edges.

SAFETY CAUTION for KX-TD144

The small cover which provides access to connectors CN402, CN403, CN404 and CN405 shall
not have its cable knock-out section removed, unless another expansion unit is mounted above
which would prevent finger access via the cable knock-out opening. This safety requirement is
necessary to protect users from network voltages.

D1232

DIGITAL SUPER HYBRID SYSTEM

Panasonic

Panasonic

Cord holder

D1232

DIGITAL SUPER HYBRID SYSTEM

Panasonic

Panasonic

Cut here

«
...
155
156
157
158
159
...
»

Summary of Contents for KX-TD1232NL
























































































































































































Reviews:

No comments

Related manuals for KX-TD1232NL

Brand: Yealink Pages: 4

CP930W Telesystem

Brand: Yealink Pages: 12

Brand: Yamaha Pages: 23

Brand: Uniden Pages: 48

Brand: Aastra Pages: 113

Jitterbug Smart2

Brand: GreatCall Pages: 21

CENTURION Series

Brand: NORTHERN ELECTRIC Pages: 12

Brand: Cansec Pages: 32

Brand: SoundPeats Pages: 14

Ascotel Office 35

Brand: ASCOM Pages: 68

Brand: AEG Pages: 204

Brand: Panasonic Pages: 5

KXTS15W - PHONE-LO

Brand: Panasonic Pages: 32

KXTS21W - PHONE-2 L

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 37

KXTS27W - PHONE-2 L

Brand: Panasonic Pages: 40

PanaVoice Courier

Brand: Panasonic Pages: 46

KX-TSC14W - KX TSC14 Corded Phone

Brand: Panasonic Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands