Panasonic KX-TD1232NL Installation Manual Download Page 68

Page: 68 / 183

2.4

Installation of Optional Cards and Unit

General Installation

Note

•

System Programming is required for expansion unit location. <SYS PRG [109]>
Default:
Area 1 = 4-CO Line Unit,
Area 2 = 8-Station Line Unit.

•

It is also possible to attach the line expansion unit to the DISA or Remote Unit and install
them to the main unit.

•

For unit combinations, refer to Section 1.4.2

Expansion Unit Combination.

KX-TD1232

The following expansion units can be installed to any of the three expansion areas.

Note

•

System Programming is required for expansion unit location. <SYS PRG [109]>
Default:
Area 1 = 4-CO Line Unit,
Area 2 and 3 = 8-Station Line Unit.

•

For unit combinations, refer to Section 1.4.2

Expansion Unit Combination.

Expansion

area 2

Expansion

area 3

Expansion

area 1

Expansion Unit
Connectors

Remove the cover
plate(s) on the
front cover.

8-Station Line Unit, KX-TD170:
Adds eight extensions.

4-CO Line Unit, KX-TD180:
Adds four outside lines.

Max. two extension line units

One outside line unit

Panasonic

D1232

Summary of Contents for KX-TD1232NL
























































































































































































Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands

Panasonic KX-TD1232NL, Installation Manual

Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands