Panasonic KX-TD1232NL Installation Manual Download Page 156 | Manualshive

Page: 156 / 183

background image

5.2

Wireless System Installation

156

DECT Installation

7.

Wired Extension Connection (KX-TD144 only)
A Cell Station Interface Unit can support four wired extensions as well as wireless
extensions. Use 4-pin plugs to connect the wired extensions.

a)

Insert the required telephone wires into the holes in the plug. Press the transparent part
into the black part.

Note

Do not peel off the wire coating. Insert the wires all the way.

b)

Insert the plug into a jack on the unit.

Note

Actual jack numbers for the KX-TD1232 depend on the type and location of units
connected to the system.

8.

Tie all of the cords into a bundle. If other cords are exposed in the upper cabinet, tie them
also.

9.

Close the cabinet cover and secure the outside screw.

D1

T
R
D2

D1
T
R
D2

1

2

4-pin plug

Panasonic

12

11

10

9

Jack

no.

<KX-TD816>

D1
T
R
D2

20

19

18

17

Jack

no.

<KX-TD1232>

D1
T
R
D2

C

S

IN

F

DECT

Connect the ground terminal to ground.
Note: If other expansion units are
installed, the frame ground connection
is required for only one unit.

To extensions

«
...
154
155
156
157
158
...
»

Summary of Contents for KX-TD1232NL
























































































































































































Reviews:

No comments

Related manuals for KX-TD1232NL

Brand: Panasonic Pages: 72

Brand: Olympia Pages: 28

80-6115-00 - AT&T E5813B - 5.8 GHZ Three Handset Answering System

Brand: VTech Pages: 53

Touch Tone Capture

Brand: Chase Pages: 10

Brand: Aastra Pages: 28

Brand: Uniden Pages: 52

Brand: TANDBERG Pages: 14

Brand: AT&T Pages: 4

T-Octophon F 50

Brand: T-COM Pages: 16

Brand: UCOM Pages: 24

Brand: Sony Ericsson Pages: 2

Brand: Toshiba Pages: 2

CTX IPT 1010F-SD

Brand: Toshiba Pages: 3

Brand: Toshiba Pages: 3

Control panel module for monitor 20550

Brand: Toshiba Pages: 8

Brand: US Robotics Pages: 104

Brand: Tunstall Pages: 24

Brand: ENZER Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands