Panasonic KX-TD1232NL Installation Manual Download Page 105

Page: 105 / 183

2.4

Installation of Optional Cards and Unit

General Installation

105

Hook the battery adaptor onto the screw heads.

Mounting on Concrete or Mortar Walls;

At step 4, drill two holes and drive the anchor plugs with a hammer, flush to the wall, and install
the big screws into the anchor plugs.

Note

•

If the Power LED does not go on, check the main unit, battery adaptor, batteries and wiring
connection.

•

After connection of the battery adaptor, keep the power switch on unless when the main unit
is turned off. (Batteries will discharge.)

•

To charge the discharged batteries, use a proper charging unit.

•

Power Fuse: (8 A, 32 V) 2
If the Power LED light goes off during a power failure, the power fuse may have been
blown. To change the fuse:

1. Turn the power switch off.

2. Turn the fuse holder in the direction of Arrow

while pushing it in the direction of

Arrow .

3. Change the fuse.

4. Turn the fuse holder in the direction of Arrow

while pushing it in the direction of

Arrow .

5. Turn the power switch on.

•

Back-up Duration: depends on the amp-hour rating of the batteries used.
E.g.,When using two 12 VDC batteries 20 amp-hour, maintenance-free, car batteries, the
power is maintained for about three hours.

Screws
(big)

Screws
(small)

Front

Bottom

Wall

Rear

Metal Plates

Fuse Holder

Summary of Contents for KX-TD1232NL
























































































































































































Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands

Panasonic KX-TD1232NL, Installation Manual

Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands