Panasonic KX-TD1232NL Installation Manual Download Page 82

Page: 82 / 183

2.4

Installation of Optional Cards and Unit

General Installation

Remove the front cover of the DISA or Remote Unit.
The KX-TD198 users must set the MODE switch to 2.

Attach the expansion unit to the DISA or Remote Unit as shown below. Be sure to connect
the cabinet cords by inserting the expansion unit cabinet cord through the slot in the DISA
or Remote Unit.

Remove the cover plate and connect the cabinet cord to the connector in the main unit
firmly.

Attaching another line expansion unit to the DISA Unit (KX-TD190) or Remote Unit (KX-
TD198) and install them to the system

MODE

Expansion unit cabinet cord

DISA / Remote unit
cabinet cord

Panasonic

D816

DIGITAL SUPER HYBRID SYSTEM

Panasonic

Summary of Contents for KX-TD1232NL
























































































































































































Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands

Panasonic KX-TD1232NL, Installation Manual

Search results

Summary of Contents for KX-TD1232NL

Reviews:

Related manuals for KX-TD1232NL

Brands by name

Popular brands