Panasonic FP2 -AD8 Manual Download Page 101

Page: 101 / 121

FP2 Analog Unit

Troubleshooting

13 - 3

13.1 Problems Concerning the Analog Input

13.1 Problems Concerning the Analog Input

Problem

Remedy

Analog input conversion value cannot

be read.

Check the I/O allocation for the analog units.
Check the range settings.
Check the settings for no execution of conversion processing (shared

memory setting).
Check the analog signal wiring.

Proper current input conversion value

cannot be obtained.

Check the terminal block wiring.
Check the current input devices.

Conversion value is unsteady.

Make sure that you are using shielded twisted-pair wiring for the input

signal wires.
Make sure that the shielding of the shielded twisted-pair wiring is proper-

ly connected.
Make sure that no input signal wires are near other power wires.

Proper conversion value cannot be

obtained during R.T.D. Pt100

connection.

Check the range settings.
Check the three-wire wiring and restart the equipment.

Proper conversion value cannot be

obtained during thermocouple

connection.

Check the range settings.
Check the polarity of the thermocouple.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for FP2 -AD8


























































































































Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands

Panasonic FP2 -AD8, Manual

Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands