Panasonic FP2 -AD8 Manual Download Page 14

Page: 14 / 121

FP2 Analog Unit

Functions and Restrictions

1 - 8

1.5

Current Consumption

1.5

Current Consumption

The internal current consumption values for the FP2 analog units noted below.
When the system is configured, the other units being used should be taken into

consideration, and a power supply unit with a sufficient capacity should be used.

Name

Order number

Current consumption (at 5 V DC)

CPU unit with analog I/O

FP2-C1A

1,060mA or less

Analog input unit

FP2-AD8

500mA or less

Analog output unit

FP2-DA4

600mA or less

For information on restrictions applying to combinations based on current consumption,

refer to the FP2 hardware manual and each unit’s manuals.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for FP2 -AD8


























































































































Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands

Panasonic FP2 -AD8, Manual

Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands