Panasonic FP2 -AD8 Manual Download Page 33

Page: 33 / 121

FP2 Analog Unit

Setting the I/O Range and I/O Allocation

4 - 3

4.1

Setting the Input and Output Range

4.1

Setting the Input and Output Range

Set the analog input and output range using the range setting switch on back side of unit.

4.1.1

Setting the Analog Input Range

When setting the same range for the all the channels at once, you can only use the range

setting switch. Use 1 to 5 of the range setting switch for both the CPU unit with analog

I/O and analog input units. Use the table below as a base and set the range setting switch

for the input range you will use.
If you will be using different input ranges together, then set the range setting switch to

“Enable setting by software.” Also, for the analog input initial settings, you must set the

range for each unit by the sequence program.
For detailed information

section 5.1

+/-10V
+/-20mA

1 to 5V
4 to 20mA

+/-100mV

Thermocouple J

Thermocouple K

Thermocouple R

Thermocouple S

Thermocouple T

R.T.D (Pt100)

R.T.D (Pt1000)

Not used

Enable setting

by software

Note

Be sure that range setting switches No.6 to 8 are off before use. If

they are on, operation will not be normal.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for FP2 -AD8


























































































































Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands

Panasonic FP2 -AD8, Manual

Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands