Panasonic FP2 -AD8 Manual Download Page 102

Page: 102 / 121

FP2 Analog Unit

Troubleshooting

13 - 4

13.2 Problems Concerning the Analog Output

13.2 Problems Concerning the Analog Output

Problem

Remedy

Proper analog output cannot be

obtained.

Make sure that the FP2 CPU unit is in RUN mode.
Check the I/O allocation for the analog units.
Check the range settings.
Check the settings for no execution of conversion processing (shared

memory setting).
Make sure that the analog output data given to the analog unit is proper

for the range.
For current output, make sure that the impedance of the output load

device is 300

Ω

or less.

Check the analog signal wiring.

Analog output value is unsteady.

Make sure that you are using shielded twisted-pair wiring for the output

signal wires.
Make sure that the shielding of the shielded twisted-pair wiring is proper-

ly connected.
Make sure that no output signal wires are near other power wires.
Check the sequence program that gives the output data to the analog

unit.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for FP2 -AD8


























































































































Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands

Panasonic FP2 -AD8, Manual

Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands