Panasonic FP2 -AD8 Manual Download Page 29

Page: 29 / 121

FP2 Analog Unit

Wiring

3 - 7

3.3 Wiring for Analog Output

3.3

Wiring for Analog Output

3.3.1

Voltage Output (

10V range)

V n

COM

I n

Ch n

Output terminals

Load equipment

Shielded wire

3.3.2

Current Output (0 to 20mA range)

V n

COM

I n

Ch n

Output terminals

Load equipment

Shielded wire

3.3.3

Precautions Regarding Analog Output Wring

For the analog output wiring, always use double-core twisted-pair shielded wires.
Ground the shielding of the shielded wires at the side of the load devices. However,

depending on the conditions of the external noise, it may be necessary to ground

externally, or leave the shielding open.
Do not have the analog output wiring close to AC wires, power wires, or load wires from

sources other than the PLC.
The terminals marked with a dot on the input and output terminal blocks are not to be

used. However, they may be connected to circuits internally, so be sure not to connect

any wiring to them.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for FP2 -AD8


























































































































Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands

Panasonic FP2 -AD8, Manual

Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands