Panasonic FP2 -AD8 Manual Download Page 97

Page: 97 / 121

FP2 Analog Unit

Sample Program for Analog Output Hold Setting

12 - 5

12.2 Output Hold (Any Value) Setting Program

12.2.2

Basic Program (Analog Output Unit)

Program outline

When switching from the RUN mode to the PROG. mode, this program holds the analog

output at any desired value according to the shared memory (addresses 17 to 21)

settings. Then the program writes the data stored in data register DT100 to DT103 to the

output relay areas WY0 to WY3 of output channels ch 0 to ch 3 for the analog output unit.

Settings

I/O allocation

I/O number

Contents

WY0

Analog output data for ch 0

WY1

Analog output data for ch 1

WY2

Analog output data for ch 2

WY3

Analog output data for ch 3

Shared memory

Address 17

Analog output hold setting
H0: Non-hold
H1: Hold (holds analog output at final value of RUN mode)
H2: Hold (holds analog output at any desired value)

Address 18 to 21

Analog output hold data (any value) setting
Range of any value setting

-10 to +10V output range: K-2048 to K2047

0 to 20mA output range: K0 to K4095

For detailed information

section 14.3.3

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for FP2 -AD8


























































































































Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands

Panasonic FP2 -AD8, Manual

Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands