Panasonic FP2 -AD8 Manual Download Page 111

Page: 111 / 121

FP2 Analog Unit

Specifications

14 - 9

14.3 Table of Shared Memory Area

Address 10 can only be written to after the first conversion is

complete when the power is turned on.

Addresses 18 to 21 can only be written to once using a user

program after RUN. Reading is possible all the time.

Regarding the preparation complete flag for analog input of

address 10, when switching from PROG.to RUN mode, the

preparation complete flags of all channels will turn on because

all channels are undergoing conversion execution. When the

non-execution setting for each channel is set, this is reflected

in the bit that corresponds to address 10.

When “Enable setting by software” is specified at the range

setting switch, the address 10 “analog input preparation

complete flag” will not turn on because conversion will not

take place until the range setting is performed.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for FP2 -AD8


























































































































Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands

Panasonic FP2 -AD8, Manual

Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands