Panasonic FP2 -AD8 Manual Download Page 13

Page: 13 / 121

FP2 Analog Unit

Functions and Restrictions

1 - 7

1.4 Installation Restrictions

1.4

Installation Restrictions

1.4.1

CPU Unit with Analog I/O

Can only be installed the CPU unit with analog I/O to the immediate right of the power

supply unit on the CPU backplane (where the CPU unit is normally located).
Cannot be installed the CPU unit with analog I/O on an expansion backplane.

CPU backplane

CPU unit with analog I/O

Expansion backplane

Expansion

cable

Cannot be installed here

Cannot be installed on an

expansion backplane

1.4.2

Analog Input Unit and Analog Output Unit

There are no restrictions regarding the installation position when installed on the CPU

backplane or expansion backplane.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for FP2 -AD8


























































































































Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands

Panasonic FP2 -AD8, Manual

Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands