Panasonic FP2 -AD8 Manual Download Page 114

Page: 114 / 121

FP2 Analog Unit

Specifications

14 - 12

14.3 Table of Shared Memory Area

14.3.3

Shared Memory of Analog Output Unit

Address Descriptions

Initial value See section

Output hold setting for analog output ch 0 to 3

H0000

14.5.1

Output hold (any value) data setting for analog output ch 0

K0000

14.5.2

Output hold (any value) data setting for analog output ch 1

K0000

Output hold (any value) data setting for analog output ch 2

K0000

Output hold (any value) data setting for analog output ch 3

K0000

No execution of conversion processing setting for analog output ch 0 to 3 H1111

14.5.3

Notes

Shared memory addresses other than those listed above are

not used. Do not perform reading and writing with addresses

that are not used.

The shared memory addresses are all preset when the power

is turned from off to on (they return to the initial values).

Addresses 17 to 22 can be written to by the program as many

times as desired when the mode is changed from the PROG.

mode to the RUN mode.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for FP2 -AD8


























































































































Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands

Panasonic FP2 -AD8, Manual

Search results

Summary of Contents for FP2 -AD8

Reviews:

Related manuals for FP2 -AD8

Brands by name

Popular brands