![background image](http://html1.mh-extra.com/html/panasonic/dp-c321/dp-c321_service-handbook_3758375148.webp)
3-74
Chapter 3 Troubleshooting
012-120 COMPILER ENTRANCE SENSOR ON JAM
Description
The COMPILER ENTRANCE SENSOR did not
detect paper within the specific time after the H-TRA EXIT
SENSOR has detected the paper. (The specified time differs
depending on the paper size.)
BSD on : CH11.5 CH11.11A
DC330 Codes to be checked
DC330
[012-101] COMPILER ENTRANCE SENSOR
DC330
[012-001] FINISHER DRIVE MOTOR
Check Items
• The SENSOR ACTUATOR for breakage and bending
• The paper path failure for burr and foreign substance, etc.
• The DECURLER ROLLER/PINCH ROLLER for a
revolution failure
• The Drive Transmission Gear from the FINISHER DRIVE
MOTOR for wear and breakage
012-122 COMPILER ENTRANCE SENSOR OFF JAM
Description
Paper does not pass through the COMPILER
ENTRANCE SENSOR within the specific time after the
COMPILER ENTRANCE SENSOR has detected the paper.
(The specified time differs depending on the paper size.)
BSD on : CH11.5 CH11.11A
DC330 Codes to be checked
DC330
[012-101] COMPILER ENTRANCE SENSOR
DC330
[012-001] FINISHER DRIVE MOTOR
Check Items
• The Sensor Actuator for return failure
• The paper path failure for burr and foreign substance, etc.
• The Drive Transmission Gear from the FINISHER DRIVE
MOTOR for wear and breakage
• The DECURLER ROLLER/PINCH ROLLER for a
revolution failure
• The COMPILER ENTRANCE ROLLER for a revolution
failure
012-170 SET EJECT JAM
Description
The voltage level of the COMPILER PAPER
SENSOR did not change within 400 ms after the EJECT
MOTOR has turned On.
BSD on : CH11.6 CH11.11B
DC330 Codes to be checked
DC330
[012-102] COMPILER PAPER SENSOR
DC330
[012-030 to 034] EJECT MOTOR
Check Items
• The EJECT ROLLER for contamination, wear and a
revolution failure
• The Drive Transmission Gear from the EJECT MOTOR
for wear and breakage
• The EJECT CLAMP for an UP/DOWN operation failure
• The STACKER TRAY for foreign substance
012-241 STAPLE MOVE SENSOR ON FAILURE
Description
In either one of the following cases:
• The STAPLE MOVE SENSOR did not turn On within
2sec after the system has started to move to the STAPLE
POSITION and the STAPLE MOVE SENSOR has turned
Off.
• The STAPLE MOVE SENSOR did not turn On after the
move to the STAPLE POSITION has completed.
BSD on : CH11.7 CH11.11B
Procedure
Open the FINISHER FRONT COVER. Turn the
STAPLE HEAD ASSEMBLY manually.
Does the STAPLE HEAD move smoothly without any load?
Y
N
Remove the cause of STAPLE HEAD not moving, such as
rail breakage, drag, and gnawed gear.
Cheat the FRONT COVER INTERLOCK SWITCH.
Enter and run
DC330
[012-224].
Turn On/Off the STAPLE MOVE SENSOR with paper, etc.
Is the display switched between H and L?
Y
N
Repair the STAPLE MOVE SENSOR using the Generic
Permeable Sensor Failure FIP.
Execute
DC330
[012-081] (FRONT direction) or
DC330
[012-
083] (REAR direction).
Was the STAPLE MOVE MOTOR activated?
Y
N
Is +24 VDC measured between the FINISHER PWB J847-
3 (+) and GND (-)?
Y
N
Is +24 VDC measured between the FINISHER PWB
J844-4 (+) and GND (-)?
Y
N
Check the INTLK ON +24 VDC circuit to the
FINISHER PWB J844-4 by referring to the BSD
CH11.1.
Replace the FINISHER PWB. (PL15.13)
Check the wire between the FINISHER PWB J847 and the
STAPLER MOVE MOTOR J888 for an open circuit or
poor contact. If no problems are found, replace the
STAPLER MOVE MOTOR (PL15.9) and the FINISHER
PWB (PL15.13) in sequence.
Replace the FINISHER PWB. (PL15.13)
Though it is possible to run the following Diag on
the machine not installed with the Finisher, an error
will be displayed.
Though it is possible to run the following Diag on
the machine not installed with the Finisher, an error
will be displayed.
Though it is possible to run the following Diag on
the machine not installed with the Finisher, an error
will be displayed.
Though it is possible to run the following Diag on
the machine not installed with the Finisher, an error
will be displayed.
Summary of Contents for DP-C321
