manualshive.com logo in svg

Omron NYP17-*-11 SERIES, User Manual

Share
Download
Omron NYP17-*-11 SERIES User Manual Download Page 151

Star Earthing

If the earthing method used for the building is not equipotential bonding or the earthing system is un-
known, choose (a) from among the earthing methods given below.
(a) Connecting devices and noise sources to separate earth electrodes

This is an earthing method to separately ground an earth electrode of the device that is connected
with a communications cable or other devices and an earth electrode of a high-power device that
could be a noise source, such as a motor or inverter.
Each earth electrode must be ground to 100 Ω or less.
Connect the ground lines of the device that is connected with a communications cable and other
devices as a bundle to a single earth electrode. Be sure that the earth electrode is separated by a
minimum of 10 m from any other earth electrode of a device that could be a noise source.

10 m min.

Hub

PLC

Control panel

Other device

A device that could be 
a noise source

NY-series
Industrial Box PC

NY-series
Industrial Panel PC

(b) Connecting devices and noise sources to a common earth electrode

This is an earthing method to connect the device that is connected with a communications cable,
other devices, and a device that could be a noise source, to a common earth electrode.
This earthing method is not recommended because the device that could be a noise source may
interfere electromagnetically with other devices.

Hub

PLC

Control panel

Other device

A device that could be 
a noise source

NY-series
Industrial Box PC

NY-series
Industrial Panel PC

5 Installation

5 - 31

NY-series Industrial Panel PC User's Manual (W555)

5-4
 W
ire

5

5-4-2 Ground

Summary of Contents for NYP17-*-11 SERIES









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands