manualshive.com logo in svg

Omron NYP17-*-11 SERIES, User Manual

Share
Download
Omron NYP17-*-11 SERIES User Manual Download Page 142

• Power lines and signal lines
• Input signals and output signals
• Analog signals and digital signals
• High-level signals and low-level signals
• Communications lines and power lines
• DC signals and AC signals
• High-frequency devices (such as Inverters) and signal lines (communications)

(Routing of) Wiring

Observe the following points when wiring power supply and signal cables.
• When routing signal cables with differing characteristics through the same duct, always keep

them separated.

• As much as possible, avoid routing multiple power supply lines through the same duct. If it can-

not be avoided, then construct a partition between them in the duct and ground the partition.

Partitioning Methods for Signal and Power Supply Cables

(a)

(b)

(c)

(d)

Signal cables

Signal cables

Signal cables

Power supply cables

a

Power supply cables

Partition

Signal

cables

(group A)

Signal

cables

(group B)

Signal

cables

(group C)

• To avoid overheating the conduits when using conduits for wiring, do not place wires for a single

circuit in separate conduits.

Parallel Wiring (Single Phase)

Correct

Correct

Power supply

Incorrect

Power supply

Power supply

Load

Load

Load

Conduits

Conduits

Conduits

NG

OK

OK

5 Installation

5 - 22

NY-series Industrial Panel PC User's Manual (W555)

Summary of Contents for NYP17-*-11 SERIES









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands