manualshive.com logo in svg

Olympus AL120-6 Series, Operation Manual, Page: 75 / 80

Share
Download
Olympus AL120-6 Series Operation Manual Download Page 75

Operation Manual 

Troubles and Countermeasures

 / Automatic Unloading

 

 

 

 

 

5-9 

Page 

1  During the Top Macro Inspection 

When  the  loader  has  stopped  with  a  wafer  held  on  the  macro  table,  the 

vacuum  remains  on.  Unload  the  wafer  according  to  the  following 

procedure. 

 

1. 

If  the  main  switch  is  turned  ON,  the  loader  will  not  operate  but  will 

indicate the warning code [W0005], still holding the wafer.   

2. 

Removing the wafer using tweezers:

 

Press the [Start] button 

 and the macro table lowers and becomes 

horizontal,  and  the  vacuum  turns  off.  Remove  the  wafer  using 

tweezers or similar tools. 

3. 

Unloading the wafer automatically:

 

Using  the  Wafer  No.  selector  buttons,  specify  the  number  of  the 

cassette slot to unload the wafer. 

4. 

The LED in the specified Wafer No. selector button lights up. 

5. 

Press the [Unload] button 

. 

6. 

After  wafer  mapping  is  completed,  the  wafer  is  automatically 

unloaded into the specified slot. 

 

2  During the Back Macro Inspection 

When the loader has stopped with a wafer held on the L-arm, the vacuum 

remains on. Unload the wafer according to the following procedure. 

 

1. 

If  the  main  switch  is  turned  ON,  the  loader  will  not  operate  but  will 

indicate the warning code [W0006], still holding the wafer. 

2. 

Removing the wafer using tweezers:

 

Press the [Start] button 

, and the wafer is transferred to the macro 

table and the vacuum turns off. Remove the wafer using tweezers or 

similar tools. 

3. 

Unloading the wafer automatically:

 

Using  the  Wafer  No.  selector  buttons,  specify  the  number  of  the 

cassette slot to unload the wafer. 

4. 

The LED in the specified Wafer No. selector button lights up. 

5. 

Press the [Unload] button. 

6. 

After  wafer  mapping  is  completed,  the  wafer  is  automatically 

unloaded into the specified slot. 

 

 

 

 

 

 

Summary of Contents for AL120-6 Series

















































































Reviews:

No comments