manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual


Share
Download
background image

1-3-23

Contents

Sets the phone number indicated at the service call error.

Purpose

Execute to set the service telephone number at the installation of the machine.

Setting

1.Press the [Start] key.

*: Input keys are indicated on the touch panel.

2.Input telephone number (15 digits maximum).
3.Press the [Start] key to set the setting value.

Completion

Press the [Stop] key.

*: The screen for selecting a maintenance item No. is displayed.

Contents

Sets or displays the machine serial number.

Purpose

Checks the machine serial number
After the main/engine PWB replacement, execute if the "C0180 machine number mismatch" occurs.

Caution

Do not execute U004, select [Execute] and press [Start] key if the machine serial number in the engine 
PWB is different from the main unit serial number. A different machine serial number is overwritten in the 
main PWB.

Execution

1.Press the [Start] key.

When the machine serial number in the engine PWB matches the one in the main PWB,

When the machine serial number in the engine PWB does not match the one in the main PWB,

Setting
Execute if the serial numbers do not match.

1.Select [Execute].
2.Press the [Start] key.

*: The serial number writing starts.

3.Turn the power switch off then on. Wait more than 5 seconds between the power off and on.

Completion

Press the [Stop] key.

*: The screen for selecting a maintenance item No. is displayed.

U003

Set Telephone Number for Service Call
(Message: Set Telephone Number for Service Call)

U004

Machine Number
(Message: Machine Number)

Items

Contents

Machine No.

Displays the machine serial number.

Items

Contents

Machine No.(Main)

Displays the machine serial number in the main PWB.

Machine No.(Eng)

Displays the machine serial number in the engine PWB.

Y11

8

240-1

Service Manual

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for d-Copia 3002MF plus

Canon ImageCLASS MF4570dw Basic Operation Manual preview
ImageCLASS MF4570dw
Brand: Canon Pages: 164
Canon imagePRESS C800 Series Service Manual preview
imagePRESS C800 Series
Brand: Canon Pages: 132
Canon ImageCLASS MF5730 Technical Information preview
ImageCLASS MF5730
Brand: Canon Pages: 2
Xerox 5700 Series Manual preview
5700 Series
Brand: Xerox Pages: 25
IBM RS/6000 44P Series 270 User Manual preview
RS/6000 44P Series 270
Brand: IBM Pages: 216
Oki Okipage8z Limited Warranty preview
Okipage8z
Brand: Oki Pages: 16
Olivetti PR2 plus Service Manual preview
PR2 plus
Brand: Olivetti Pages: 179
Olivetti JS-505 Service Manual preview
JS-505
Brand: Olivetti Pages: 36
Oki B6200 Series Maintenance Manual preview
B6200 Series
Brand: Oki Pages: 679
Oki PRO511DW Manual preview
PRO511DW
Brand: Oki Pages: 40
OKIDATA Pacemark 3410 Service Handbook preview
Pacemark 3410
Brand: OKIDATA Pages: 308
OKIDATA Pacemark 3410 Instruction Manual preview
Pacemark 3410
Brand: OKIDATA Pages: 9
OKIDATA MICROLINE 320 Quick Manual preview
MICROLINE 320
Brand: OKIDATA Pages: 2
Oki Microline 8480 FB Setup Manual preview
Microline 8480 FB
Brand: Oki Pages: 12
Canon imagePROGRAF GP-540 Setup Manual preview
imagePROGRAF GP-540
Brand: Canon Pages: 82
Xerox Docutech 6100 Planning Manual preview
Docutech 6100
Brand: Xerox Pages: 16
Xerox DocuTech 6155 Specification Sheet preview
DocuTech 6155
Brand: Xerox Pages: 2
Xerox Docutech 6100 Release Note preview
Docutech 6100
Brand: Xerox Pages: 2

Brands by name

Popular brands

Load more brands