manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual, Page: 478 / 752

Share
Download
Olivetti d-Copia 3002MF plus Service Manual Download Page 478

2-2-2

7. LCD PWB (LCDPWB)........................... Controls the LCD display.
8. CCD PWB (CCDPWB).......................... Reads the image of originals.
9. APC PWB (APCPWB) .......................... Generates and controls the laser beam.

10. NFC PWB (NFCPWB) .......................... Antenna circuit for wireless communication.

11. Drum PWB (DRPWB) ........................... Relays wirings from electrical components on the drum unit.

Drum individual information in EEPROM storage.

12. Drum relay PWB (DRRPWB)................ Consists of wiring relay circuit between engine PWB and the

drum unit.

13. Developing PWB (DEVPWB)................ Relays wirings from electrical components on the developing unit.

Developing individual information in EEPROM storage.

14. Developing relay PWB (DEVRPWB) .... Consists of wiring relay circuit between engine PWB and the

developer unit and contain the temperature sensor inside the 
machine.

15. RFID PWB (RFPWB) ............................ Reads the container information.
16. LED PWB (LEDPWB) ........................... Exposes originals.
17. Touch Panel (TP) .................................. Operation panel.
18. USB  PWB (USBPWB) ......................... USB PWB slot distribution.

List of correspondences of PWB names

No.

Name used in service manual

Name used in parts list

1

Main PWB (MPWB)

PATRS PWB MAIN ASSY SP

2

Engine PWB (EPWB)

PATRS PWB ENGINE ASSY SP

3

High voltage PWB (HVPWB)

PARTS HIGH VOLTAGE SP

4

Power source PWB (PSPWB)

PARTS LOW VOLTAGE 100 SP
PARTS LOW VOLTAGE 200 SP

5

Operation panel PWB 1 (OPPWB 1)

PARTS OPERATION UNIT SP

6

Operation panel PWB 2 (OPPWB 2)

7

LCD PWB (LCDPWB)

8

CCD PWB (CCDPWB)

PARTS ISU

9

APC PWB (APCPWB)

LK-7105

10

NFC PWB (NFCPWB)

PARTS PWB NFC ASSY SP

11

Drum PWB (DRPWB)

DK-7105

12

Drum relay PWB (DRRPWB)

PARTS PWB DRUM CONNECT ASSY SP

13

Developing PWB (DEVPWB)

DV-7105

14

Developing relay PWB (DEVRPWB)

PARTS DEVE CONNECT ASSY SP

15

RFID PWB (RFPWB)

PARTS PWB RFID ASSY SP

16

LED PWB (LEDPWB)

PARTS PWB SCANNER LED ASSY SP

17

Touch panel (TP)

PARTS OPERATION UNIT SP

18

USB PWB (USBPWB)

PARTS PWB USB HUB ASSY SP

Y11

8

240-1

Service Manual

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments