manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual


Share
Download
background image

1-4-73

(7) Streaks are printed horizontally.

(8) A part of image is dark or light.

(9) Spots are printed.

Print example

Causes

Check procedures/corrective measures

Dirty or flawed drum.

Perform the drum refresh operation.
Flawed drum. Replace the drum unit (see page 1-5-21).

Dirty developer section.

Clean any part contaminated with toner in the developer 
section.

Poor contact of grounding ter-
minal of drum unit.

Check the installation of the drum unit. If it operates incor-
rectly, replace it (see page 1-5-21).

Print example

Causes

Check procedures/corrective measures

Defective exposure lamp.

Replace the LED PWB (see page 1-5-37).

One-side-only closure of the 
right cover.

Close the right over again.

The transfer unit is not prop-
erly attached.

Reattach the transfer roller. Or replace the transfer roller 
unit.

The developer unit is sepa-
rated from the drum unit.

Clean the developer pulley. Or replace the developer unit.

Clean the Drum. Or relpace the drum unit.

Dirty laser scanner unit dust 
shield glass.

Perform the laser scanner unit dust shield glass cleaning.

Print example

Causes

Check procedures/corrective measures

Dirty contact glass. 

Clean the contact glass.

Dirty or flawed drum.

Perform the drum refresh operation.
Flawed drum. Replace the drum unit (see page 1-5-21).

Dirty or flawed chager roller.

Clearn the chager roller.
Or replace the chager roller unit (see page 1-5-23).

Deformed or worn cleaning 
blade in the drum unit.

Replace the drum unit (see page 1-5-21).

Flawed developer roller.

Replace the developer unit (see page 1-5-18).

Dirty heat roller and press 
roller.

Clean the heat roller and press roller.

Y11

8

240-1

Service Manual

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for d-Copia 3002MF plus

VASTEX E-1000 Assembly And Operation Instructions Manual preview
E-1000
Brand: VASTEX Pages: 15
Xante Ilumina Repacking And Shipping Manual preview
Ilumina
Brand: Xante Pages: 6
Datamax ST-3210 Quick Start Manual preview
ST-3210
Brand: Datamax Pages: 2
Xerox DocuPrint C3055 DX Settings Manual preview
DocuPrint C3055 DX
Brand: Xerox Pages: 20
TallyGenicom LA800 Quick Start Manual preview
LA800
Brand: TallyGenicom Pages: 166
Panasonic KX-MC6040 - Color Laser Multi-Function... Quick Reference Manual preview
KX-MC6040 - Color Laser Multi-Function...
Brand: Panasonic Pages: 24
Xerox WorkCentre PRO 35 Specifications preview
WorkCentre PRO 35
Brand: Xerox Pages: 13
Aficio MP1900 Service Manual preview
MP1900
Brand: Aficio Pages: 188
Xerox WorkCentre 6400XF Evaluator Manual preview
WorkCentre 6400XF
Brand: Xerox Pages: 24
Oki OkiPos 407II Installation Manual preview
OkiPos 407II
Brand: Oki Pages: 8
U-Line DYMO LABELWRITER 450 TURBO H-1265 Manual preview
DYMO LABELWRITER 450 TURBO H-1265
Brand: U-Line Pages: 9
TVS electronics MINI THERMAL RP-3180 User Manual preview
MINI THERMAL RP-3180
Brand: TVS electronics Pages: 19
Xerox VersaLink C400 Manual preview
VersaLink C400
Brand: Xerox Pages: 4
Wasp WPL206 Series User Manual preview
WPL206 Series
Brand: Wasp Pages: 46
Lexmark 4039 - B/W Laser Printer Parts List preview
4039 - B/W Laser Printer
Brand: Lexmark Pages: 49
Lexmark 5200 Series Setup preview
5200 Series
Brand: Lexmark Pages: 64
DataCard 150i Owner'S Manual preview
150i
Brand: DataCard Pages: 36
Lexmark CS748de Brochure & Specs preview
CS748de
Brand: Lexmark Pages: 8

Brands by name

Popular brands

Load more brands