manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual


Share
Download
background image

1-4-82

1-4-6  Send error code

This section describes the scanning errors and descriptions, preventive actions, as well as corrective actions.
Error codes not described here could fall within software errors.
If such an error is encountered, turn power off then on, and advise the service representative.

(1) Scan to SMB error codes

Code

Contents

Check procedures/corrective measures

1101

Host destined does not exist on the net-
work.

1. Confirm the destined host.
2. Confirm thedevice's network parameters.
3. Confirm the parameters of the network to which the

device is connected are correct.

1102

Login to the host has failed.

1. Confirm user name and password.
2. Confirm the parameters of the network to which the

device is connected are correct.

3. Check the host if the folder is properly shared.

1103

Destined host, folder, and/or file names 
are invalid.

1. Check illegal characters are not contained within

these names.

2. Check the name of the folder and files conform with

the naming syntax.

3. Confirm destined host and folder.

1105

SMB protocol is not enabled.

1. Confirm device's SMB protocols.

2101

Login to the host has failed.

1. Confirm  the destined host.
2. Confirm that the LAN cable is properly connected to

the device.

3. Check the SMB port number.
4. Confirm the device's network parameters.
5. Confirm the parameters of the network to which the

device is connected are correct.

2201

Writing scanned data has failed.

1. Check the file name to save the scanned data.
2. Confirm the device's network parameters.
3. Confirm the parameters of the network to which the

device is connected are correct.

2203

No response from the host during a cer-
tain period of time.

1. Confirm the network parameters the device is con-

nected.

2. Confirm that the LAN cable is properly connected to

the device.

Y11

8

240-1

Service Manual

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for d-Copia 3002MF plus

Canon imagePROGRAF W8400 Driver Manual preview
imagePROGRAF W8400
Brand: Canon Pages: 24
Canon imagePROGRAF TZ-30000 Setup Manual preview
imagePROGRAF TZ-30000
Brand: Canon Pages: 66
Canon imagePROGRAF W7200 Setup Manual preview
imagePROGRAF W7200
Brand: Canon Pages: 126
Canon imagePROGRAFi iPF840 series Basic Manual preview
imagePROGRAFi iPF840 series
Brand: Canon Pages: 149
Canon IPF850 Basic Manual preview
IPF850
Brand: Canon Pages: 166
Canon iP4000 - PIXMA Photo Printer Start Here preview
iP4000 - PIXMA Photo Printer
Brand: Canon Pages: 2
Olympus P 400 Firmware Upgrade Manual preview
P 400
Brand: Olympus Pages: 3
Canon BW Remote Operators Software Kit-A1 Service Manual preview
BW Remote Operators Software Kit-A1
Brand: Canon Pages: 20
Canon imageRUNNER 2420 Trouble Error Codes List preview
imageRUNNER 2420
Brand: Canon Pages: 30
Canon IPF850 Service Manual preview
IPF850
Brand: Canon Pages: 51
Canon imageCLASS LBP325dn Service Manual preview
imageCLASS LBP325dn
Brand: Canon Pages: 252
Xerox 4520 User Manual preview
4520
Brand: Xerox Pages: 310
Oki C6150dn Material Safety Data Sheet preview
C6150dn
Brand: Oki Pages: 48
Oki B2500 MFP Guía Del Usuario preview
B2500 MFP
Brand: Oki Pages: 42
Oki B2500 MFP Setup Manual preview
B2500 MFP
Brand: Oki Pages: 2
Oki C810n Accessory Installation Manual preview
C810n
Brand: Oki Pages: 8
Oki B 4600n Installation And Training Module preview
B 4600n
Brand: Oki Pages: 13
Oce CS9065 Features & Specifications preview
CS9065
Brand: Oce Pages: 2

Brands by name

Popular brands

Load more brands