manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual


Share
Download
background image

1-4-41

8090

DF paddle motor error

When the DF paddle motor is 
driven, DF paddle sensor 
does not turn on within 1 s.

DF paddle motor

1. Execute U240 Motor - Beat to check the

finisher operation (see page 1-3-94).

2. Check that the paddle can rotate.
3. Check that the drive from the motor

reaches the paddle.

4. Confirm that the wiring connector is

firmly connected and, if necessary,
connect the connector all the way in.
DF paddle motor and DF main PWB
(YC15) (3000-sheet finisher)
DF paddle motor and DF main PWB
(YC11) (1000-sheet finisher)

5. If the wiring is disconnected, shorted or

grounded, replace the wiring.

6. Replace the DF paddle motor.

DF paddle sensor 

1. Execute U241 Finisher - Lead Paddle to

check the finisher switch (see page 1-3-
96).

2. Check that the sensor and its mounting

bracket are correctly positioned.

3. Confirm that the wiring connector is

firmly connected and, if necessary, 
connect the connector all the way in.
DF paddle sensor  and DF main PWB 
(YC22) (3000-sheet finisher)
DF paddle sensor  and DF main PWB 
(YC20) (1000-sheet finisher)

4. Replace the DF paddle sensor.

DF main PWB

Replace the DF main PWB.

Code

Contents

Related parts

Check procedures/

corrective measures

Y11

8

240-1

Service Manual

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for d-Copia 3002MF plus

Samsung CLP-680ND: CLP-775ND Quick Installaion Manual preview
CLP-680ND: CLP-775ND
Brand: Samsung Pages: 2
Macherey-Nagel NANOCOLOR UV/VIS II User Manual preview
NANOCOLOR UV/VIS II
Brand: Macherey-Nagel Pages: 6
GE TermiNet 300 Beginner'S Manual preview
TermiNet 300
Brand: GE Pages: 16
KIP KIP 7000 Parts Manual preview
KIP 7000
Brand: KIP Pages: 103
Cino VERSAJET MP3200 Series User Manual preview
VERSAJET MP3200 Series
Brand: Cino Pages: 18
Citizen CT-E601 User Manual preview
CT-E601
Brand: Citizen Pages: 88
GCC Technologies Elite 21DN+ Getting Started Manual preview
Elite 21DN+
Brand: GCC Technologies Pages: 80
Oki B2520 MFP Guia Do Usuário preview
B2520 MFP
Brand: Oki Pages: 76
Triumph Adler DC 6140 Quick Manual preview
DC 6140
Brand: Triumph Adler Pages: 4
Sharp MX 3501N - Color Laser - Copier Brochure & Specs preview
MX 3501N - Color Laser - Copier
Brand: Sharp Pages: 8
Sharp MFP Series Brochure & Specs preview
MFP Series
Brand: Sharp Pages: 12
Sharp M1054 Brochure & Specs preview
M1054
Brand: Sharp Pages: 12
Sharp FO-IS115N Specifications preview
FO-IS115N
Brand: Sharp Pages: 2
Sharp IMAGER AR-5316 Quick Reference Manual preview
IMAGER AR-5316
Brand: Sharp Pages: 14
Sharp MX 3070 Troubleshooting Manual preview
MX 3070
Brand: Sharp Pages: 56
Sharp FS-C1020MFP Operation Manual preview
FS-C1020MFP
Brand: Sharp Pages: 32
Sharp Gemini II Plus MX-2614N Technical Handy Manual preview
Gemini II Plus MX-2614N
Brand: Sharp Pages: 41
Sharp IMAGER AR-5316 Service Manual preview
IMAGER AR-5316
Brand: Sharp Pages: 56

Brands by name

Popular brands

Load more brands