manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual


Share
Download
background image

2-1-1

2-1 Mechanical Construction

2-1-1  Paper feed/conveying section

The paper feed/conveying section consists of the paper feed unit that feeds paper from the cassette and the 
MP tray paper feed unit that feeds paper from the MP tray, and the paper conveying section that conveys the 
feed paper to the transfer/separation section.

(1) Cassette paper feed section

The cassette can contain 500 sheets. The sheet from the cassette is pulled out by rotation of the pickup roller 
and sent to the paper conveying section by rotation of the paper feed roller. Also the retard roller prevents mul-
tiple feeding of paper.

Figure 2-1-1  Cassette paper feed section

1

2

3

4

5

7

9

6

10

8

1

2

3

4

5

7

9

6

10

8

11

12

13

14

1. Pickup roller
2. Paper feed roller
3. Feed holder
4. Retard roller
5. Retard holder
6. Paper length guide
7. Bottom plate
8. Lift work plate

9. Cassette base

10. Actuator (paper sensor)

11. Cassette 1

12. Cassette 2
13. Acutuator (feed sensor 1)
14. Acutuator (feed sensor 2)

Y11

8

240-1

Service Manual

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for d-Copia 3002MF plus

Canon iR3245 Troubleshooting Manual preview
iR3245
Brand: Canon Pages: 300
Canon iR3245 Network Manual preview
iR3245
Brand: Canon Pages: 288
Canon iR3245 User Manual preview
iR3245
Brand: Canon Pages: 58
Canon iR1510 Quick Start Manual preview
iR1510
Brand: Canon Pages: 30
Panasonic Workio DP-3510 Service Handbook preview
Workio DP-3510
Brand: Panasonic Pages: 12
Panasonic Workio DP-3510 Service Manual preview
Workio DP-3510
Brand: Panasonic Pages: 858
Fastjet F500 Series Operation Manual preview
F500 Series
Brand: Fastjet Pages: 52
Xerox DocuCentre SC2020 User Manual preview
DocuCentre SC2020
Brand: Xerox Pages: 322
Xerox DocuPrint N24 Supplies Manual preview
DocuPrint N24
Brand: Xerox Pages: 2
Xerox Legacy 4112 Overview preview
Legacy 4112
Brand: Xerox Pages: 8
Xerox Phaser 4510 Advanced Features Manual preview
Phaser 4510
Brand: Xerox Pages: 80
Xerox Docutech 128 Planning Manual preview
Docutech 128
Brand: Xerox Pages: 38
Xerox WorkCentre 7132 Quick Network Setup Manual preview
WorkCentre 7132
Brand: Xerox Pages: 73
Datamax MP-Compact4 Programmer'S Reference Manual preview
MP-Compact4
Brand: Datamax Pages: 95
Datamax Mark II E-4205e Operator'S Manual preview
Mark II E-4205e
Brand: Datamax Pages: 72
Xerox Phaser 6250DP Setup Manual preview
Phaser 6250DP
Brand: Xerox Pages: 2
Xerox Phaser 6280N Evaluator Manual preview
Phaser 6280N
Brand: Xerox Pages: 16
NEC Pinwriter P6 Specification preview
Pinwriter P6
Brand: NEC Pages: 10

Brands by name

Popular brands

Load more brands