manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual


Share
Download
background image

1-3-8

 (2-1) Content of each maintenance mode

Contents

Prints the list of  the current settings of the maintenance items, paper jam and service call error occur-
rences. Output the event log and service status page.
Also, sends output data to a USB memory.

Purpose

Checks the current settings of the maintenance items, paper jam and service call error occurrences.
Before initializing or replacing the backup memory, print the list of the current settings of the maintenance 
items to reenter the settings after initialization or replacement.

Execution

1.Press the [Start] key.
2.Select the item to output.

3.Press the [Start] key to output the list.

*: If A4 paper is available, it is output with this size. If A4 paper is unavailable, select the paper source. 

Output status is displayed.

Execution: when sending output data to a USB memory

1.Press the [Start] key.
2.Insert a USB memory into the USB memory slot.
3.Select the item to send.
4.Select [USB(Text)] or [USB(HTML)].

5.Press the [Start] key.

*: The output data is sent to the USB memory.

Completion

Press the [Stop] key. 

*: The screen for selecting a maintenance item No. is displayed.

U000

 Output Maintenance Report
(Message: Output Maintenance Report)

Items

Output list

Maintenance

Maintenance mode setting status list

User Status

Output User Status Page

Service Status

Output Service Status Page

Event

Output the event log report

Network Status

Output Network Status Page

All

All reports output

Items

Output list

Print

A report is printed.

USB(Text)

Destination: send to USB memory (text format)

USB(HTML)

Destination: send to USB memory (HTML format)

Y11

8

240-1

Service Manual

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for d-Copia 3002MF plus

Oki C910 Service Manual preview
C910
Brand: Oki Pages: 282
Unisys 115 Operation/Reference Manual preview
115
Brand: Unisys Pages: 255
Xerox B210 User Manual preview
B210
Brand: Xerox Pages: 199
Oki B2200 Maintenance Manual preview
B2200
Brand: Oki Pages: 100
Oki B2200 Quick Setup Manual preview
B2200
Brand: Oki Pages: 2
Xerox B235 User Manual preview
B235
Brand: Xerox Pages: 316
Xerox B215 Get Started preview
B215
Brand: Xerox Pages: 74
Xerox B215 User Manual preview
B215
Brand: Xerox Pages: 306
Xerox B215 Quick Use Manual preview
B215
Brand: Xerox Pages: 16
Xerox B210 Quick Start Manual preview
B210
Brand: Xerox Pages: 4
Oki B2200 Guide Utilisateur preview
B2200
Brand: Oki Pages: 38
Oki B2200 Guía Del Usuario preview
B2200
Brand: Oki Pages: 38
Oki B2200 User Manual preview
B2200
Brand: Oki Pages: 36
Oki B2200 Safety & Warranty preview
B2200
Brand: Oki Pages: 36
Panasonic Workio DP-3510 Service Handbook preview
Workio DP-3510
Brand: Panasonic Pages: 12
Panasonic Workio DP-3510 Service Manual preview
Workio DP-3510
Brand: Panasonic Pages: 858
Panasonic KX-MC6260E Quick Reference Manual preview
KX-MC6260E
Brand: Panasonic Pages: 24
Oki 10i Help Manual preview
10i
Brand: Oki Pages: 40

Brands by name

Popular brands

Load more brands