manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual, Page: 12 / 752

Share
Download
Olivetti d-Copia 3002MF plus Service Manual Download Page 12

(6) Black streaks are printed vertically. ................................................................................ 1-4-72
(7) Streaks are printed horizontally. ..................................................................................... 1-4-73
(8) A part of image is dark or light........................................................................................ 1-4-73
(9) Spots are printed. ........................................................................................................... 1-4-73

(10) Image is blurred.............................................................................................................. 1-4-74
(11) The leading edge of the image is consistently misaligned with the original. .................. 1-4-74
(12) The leading edge of the image is sporadically misaligned with the original. .................. 1-4-74
(13) Paper is wrinkled. ........................................................................................................... 1-4-74
(14) Offset occurs. ................................................................................................................. 1-4-75
(15) Part of image is missing. ................................................................................................ 1-4-75
(16) Fusing is loose................................................................................................................ 1-4-75
(17) Image is out of focus. ..................................................................................................... 1-4-75
(18) Image center does not align with the original center. ..................................................... 1-4-76

1-4-4 Electric problems ................................................................................................................. 1-4-77
1-4-5 Mechanical problems........................................................................................................... 1-4-81
1-4-6 Send error code................................................................................................................... 1-4-82

(1) Scan to SMB error codes ............................................................................................... 1-4-82
(2) Scan to FTP error codes ................................................................................................ 1-4-83
(3) Scan to E-mail error codes ............................................................................................. 1-4-85

1-4-7 Error codes .......................................................................................................................... 1-4-87

(1) Error code....................................................................................................................... 1-4-87
(2) Table of general classification ........................................................................................ 1-4-88

 (2-1) U004XX error code table: Interrupted phase B ..................................................... 1-4-91
 (2-2) U006XX error code table: Problems with the unit ................................................. 1-4-92
 (2-3) U008XX error code table: Page transmission error............................................... 1-4-92
 (2-4) U009XX error code table: Page reception error .................................................... 1-4-92
 (2-5) U010XX error code table: G3 transmission........................................................... 1-4-93
 (2-6) U011XX error code table: G3 reception ................................................................ 1-4-95
 (2-7) U017XX error code table: V.34 transmission ........................................................ 1-4-96
 (2-8) U018XX error code table: V.34 reception.............................................................. 1-4-97
 (2-9) U023XX error code table: Relay command abnormal reception ........................... 1-4-97

 (2-10) U044XX error code table: Encrypted transmission ............................................... 1-4-97

1-5 Assembly and disassembly

1-5-1 Precautions for assembly and disassembly........................................................................... 1-5-1

(1) Precautions....................................................................................................................... 1-5-1
(2) Storage and handling of the drum .................................................................................... 1-5-1
(3) Storage of the toner container .......................................................................................... 1-5-1

1-5-2 OUTER COVERS.................................................................................................................. 1-5-3

(1) Detaching and attaching the front cover........................................................................... 1-5-3
(2) Detaching and attaching the rear upper cover ................................................................. 1-5-5
(3) Detaching and attaching the rear lower cover .................................................................. 1-5-5
(4) Detaching and attaching the inner tray............................................................................. 1-5-6
(5) Detaching and attaching the front upper cover................................................................. 1-5-8
(6) Detaching and attaching the eject rear cover ................................................................... 1-5-9
(7) Detaching and refitting the eject rear cover...................................................................... 1-5-9

1-5-3 Paper feed section............................................................................................................... 1-5-10

(1) Detaching and attaching the primary paper feed unit..................................................... 1-5-10
(2) Detaching and attaching the MP paper feed roller and MP separation pad ................... 1-5-11
(3) Detaching and attaching the registration cleaner ........................................................... 1-5-13
(4) Detaching and attaching the MP tray ............................................................................. 1-5-16

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments