manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual


Share
Download
background image

1-4-75

(14) Offset occurs.

(15) Part of image is missing.

(16) Fusing is loose.

(17) Image is out of focus.

Print example

Causes

Check procedures/corrective measures

Deformed or worn cleaning 
blade in the drum unit.

Replace the drum unit (see page 1-5-21).

Defective discharger lamp.

Clean the discharger lamp. Or replace the drum unit.

Defective fuser unit.

Replace the fuser unit (see page 1-5-25).

Wrong types of paper.

Check if the paper meets specifications. Replace paper.

Print example

Causes

Check procedures/corrective measures

Paper damp.

Check the paper storage conditions.

Paper creased.

Replace the paper.

Drum condensation.

Perform the drum refresh operation.

Dirty or flawed drum.

Perform the drum refresh operation.
Flawed drum. Replace the drum unit (see page 1-5-21).

Dirty transfer roller.

Clean the transfer roller. Replace the transfer roller if it is 
extremely dirty (see page 1-5-24).

Print example

Causes

Check procedures/corrective measures

Wrong types of paper.

Check if the paper meets specifications, replace paper.

Flawed heat roller or press 
roller.

Replace the fuser unit (see page 1-5-25).

Defective pressure springs.

Defective fuser heater.

Print example

Causes

Check procedures/corrective measures

Defective image scanning 
unit.

Replace the image scanning unit (see page 1-5-34).

Drum condensation.

Perform the drum refresh operation.

Y11

8

240-1

Service Manual

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for d-Copia 3002MF plus

Oki C910 Hardware preview
C910
Brand: Oki Pages: 2
Oki C910 Material Safety Data Sheet preview
C910
Brand: Oki Pages: 52
Oki C110 Manual Do Usuário preview
C110
Brand: Oki Pages: 117
Oki C110 How To Remove Jammed Paper preview
C110
Brand: Oki Pages: 45
Oki C110 Manual De L'Utilisateur preview
C110
Brand: Oki Pages: 112
Oki C110 Guías Del Usuario Manual preview
C110
Brand: Oki Pages: 115
Oki C110 Quick Setup preview
C110
Brand: Oki Pages: 2
Oki IP-6620 Maintenance Manual preview
IP-6620
Brand: Oki Pages: 572
Oki proColor pro900DP User Manual preview
proColor pro900DP
Brand: Oki Pages: 127
Olivetti d-color MF551 Printing Manual preview
d-color MF551
Brand: Olivetti Pages: 309
OKIDATA MICROLINE 320 Quick Reference Manual preview
MICROLINE 320
Brand: OKIDATA Pages: 4
Oki OKIPAGE14e Setup Manual preview
OKIPAGE14e
Brand: Oki Pages: 28
Oki OKIPAGE14e Limited Warranty preview
OKIPAGE14e
Brand: Oki Pages: 22
Canon image RUNNER 3045 Manual preview
image RUNNER 3045
Brand: Canon Pages: 14
Oki ES2024 User Manual preview
ES2024
Brand: Oki Pages: 512
Ricoh Aficio SP4100N-KP Specifications preview
Aficio SP4100N-KP
Brand: Ricoh Pages: 4
Xerox WorkCentre 7655 Detailed Specifications preview
WorkCentre 7655
Brand: Xerox Pages: 19
Olivetti d-Copia 45 Operation Manual preview
d-Copia 45
Brand: Olivetti Pages: 246

Brands by name

Popular brands

Load more brands