manualshive.com logo in svg

Olivetti d-Copia 3002MF plus, Service Manual


Share
Download
background image

1-3-67

Contents

Displays the machine serial number and drum counter history.

Purpose

Execute to check the machine serial number and drum counter values.

Method

1.Press the [Start] key.

*: Select the item to refer to.

*: Displays the machine serial number and 3 items of the drum counter history.

Completion

Press the [Stop] key.

*: The screen for selecting a maintenance item No. is displayed.

Contents

Display and clear the transfer counts for the transfer high-voltage output correction etc.

Purpose

Execute when checking the counts after replacing transfer roller unit. Also, clear the counts after replace-
ment.

Method

1.Press the [Start] key.

*:  The transfer counter value appears.

Execution: Clear

1.Select [Clear].
2.Press the [Start] key, clear the counts.

Completion

Press the [Stop] key.

*: Back to the maintenance mode No. selecting screen.

U118

Drum unit history
(Message: Drum Unit History)

Items

Contents

K

Displays the black drum history

Items

Contents

Machine History1 to 3

Machine serial number history

Cnt History1 to 3

The drum counter history

U127

Clearing the transfer count
(Message: Clear Transfer Roller Counter)

Items

Contents

Cnt

Display the transfer counts

Clear

Clear the transfer counts

Y11

8

240-1

Service Manual

Summary of Contents for d-Copia 3002MF plus

















































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for d-Copia 3002MF plus

OEC Compact Series Installation Procedure preview
Compact Series
Brand: OEC Pages: 28
Xerox Phaser 6250DP Setup Manual preview
Phaser 6250DP
Brand: Xerox Pages: 2
Xerox Phaser 6280N Evaluator Manual preview
Phaser 6280N
Brand: Xerox Pages: 16
Pinnacle Technology PP7X Series Operation Manual preview
PP7X Series
Brand: Pinnacle Technology Pages: 76
AM TECH mobile pro advance User Manual preview
mobile pro advance
Brand: AM TECH Pages: 16
Swift STP512B User Manual preview
STP512B
Brand: Swift Pages: 14
Oki OKIPOS 425D Developer'S Manual preview
OKIPOS 425D
Brand: Oki Pages: 137
A&D AD-8127 Instruction Manual preview
AD-8127
Brand: A&D Pages: 31
Pantum M6700D Series User Manual preview
M6700D Series
Brand: Pantum Pages: 164
HEIDELBERG Suprasetter 106 Operation preview
Suprasetter 106
Brand: HEIDELBERG Pages: 91
Avery Dennison M09416 TTXLI Service Manual preview
M09416 TTXLI
Brand: Avery Dennison Pages: 68
Nashuatec Aficio 9005 Operating Instructions Manual preview
Aficio 9005
Brand: Nashuatec Pages: 177
Star TSP100IIIBI Easy Setup Manual preview
TSP100IIIBI
Brand: Star Pages: 2
Oki MC770x User Manual preview
MC770x
Brand: Oki Pages: 78
Canon PIXMA MP550 Getting Started preview
PIXMA MP550
Brand: Canon Pages: 48
Canon Pixma PRO-100S series Getting Started preview
Pixma PRO-100S series
Brand: Canon Pages: 4
Canon Pixma PRO-100S series Manual preview
Pixma PRO-100S series
Brand: Canon Pages: 2
Canon PIXMA TR4520 Online Manual preview
PIXMA TR4520
Brand: Canon Pages: 570

Brands by name

Popular brands

Load more brands