manualshive.com logo in svg

NXP Semiconductors LPC5410x, User Manual, Page: 207 / 463

Share
Download
NXP Semiconductors LPC5410x User Manual Download Page 207

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

208 of 464

NXP Semiconductors

UM10850

Chapter 14: LPC5410x Standard counter/timers (CT32B0/1/2/3/4)

14.7 Register description

Each Timer/Counter contains the registers shown in 

Table 241

 ("Reset Value" refers to the 

data stored in used bits only; it does not include reserved bits content). More detailed 
descriptions follow.

 

[1]

Reset Value reflects the data stored in used bits only. It does not include reserved bits content.

Table 241. Register overview: CT32B0/1/2/3 (register base addresses 0x400B 4000 (CT32B0), 0x400B 8000 (CT32B1), 

0x4000 4000 (CT32B2), 0x4000 8000 (CT32B3), 0x4000 C000 (CT32B4))

Name

Access

Address 
offset

Description

Reset 
value

[1]

Refer- 
ence

IR

R/W

0x00

Interrupt Register. The IR can be written to clear interrupts. The IR can 
be read to identify which of eight possible interrupt sources are 
pending.

0

Table 243

TCR

R/W

0x04

Timer Control Register. The TCR is used to control the Timer Counter 
functions. The Timer Counter can be disabled or reset through the 
TCR. 

0

Table 245

TC

R/W

0x08

Timer Counter. The 32 bit TC is incremented every PR+1 cycles of 
PCLK. The TC is controlled through the TCR.

0

Table 247

PR

R/W

0x0C

Prescale Register. When the Prescale Counter (PC) is equal to this 
value, the next clock increments the TC and clears the PC.

0

Table 249

PC

R/W

0x10

Prescale Counter. The 32 bit PC is a counter which is incremented to 
the value stored in PR. When the value in PR is reached, the TC is 
incremented and the PC is cleared. The PC is observable and 
controllable through the bus interface.

0

Table 251

MCR

R/W

0x14

Match Control Register. The MCR is used to control if an interrupt is 
generated and if the TC is reset when a Match occurs.

0

Table 253

MR0

R/W

0x18

Match Register 0. MR0 can be enabled through the MCR to reset the 
TC, stop both the TC and PC, and/or generate an interrupt every time 
MR0 matches the TC. 

0

Table 255

MR1

R/W

0x1C

Match Register 1. See MR0 description.

0

Table 255

MR2

R/W

0x20

Match Register 2. See MR0 description.

0

Table 255

MR3

R/W

0x24

Match Register 3. See MR0 description.

0

Table 255

CCR

R/W

0x28

Capture Control Register. The CCR controls which edges of the 
capture inputs are used to load the Capture Registers and whether or 
not an interrupt is generated when a capture takes place.

0

Table 257

CR0

RO

0x2C

Capture Register 0. CR0 is loaded with the value of TC when there is 
an event on the CAPn.0 input.

0

Table 259

CR1

RO

0x30

Capture Register 1. See CR0 description.

0

Table 259

CR2

RO

0x34

Capture Register 2. See CR0 description.

0

Table 259

CR3

RO

0x38

Capture Register 3. See CR0 description.

0

Table 259

EMR

R/W

0x3C

External Match Register. The EMR controls the match function and the 
external match pins.

0

Table 261

CTCR

R/W

0x70

Count Control Register. The CTCR selects between Timer and 
Counter mode, and in Counter mode selects the signal and edge(s) for 
counting.

0

Table 263

PWMC

R/W

0x74

PWM Control Register. The PWMCON enables PWM mode for the 
external match pins.

0

Table 265

Summary of Contents for LPC5410x
















































































































































































































































































































































































































































































Reviews:

No comments