manualshive.com logo in svg

NXP Semiconductors LPC5410x, User Manual, Page: 300 / 463

Share
Download
NXP Semiconductors LPC5410x User Manual Download Page 300

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

301 of 464

NXP Semiconductors

UM10850

Chapter 22: LPC5410x Serial Peripheral Interfaces (SPI0/1)

A stall for Master receive can happen when a receiver overrun would otherwise occur if 
the transmitter was not stalled. In modes 0 and 2, this occurs if the previously received 
data is not read before the end of the next piece of is received. This stall happens one 
clock edge earlier than the transmitter stall.

In modes 1 and 3, the same kind of receiver stall can occur, but just before the final clock 
edge of the received data. Also, a transmitter stall will not happen in modes 1 and 3 
because the transmitted data is complete at the point where a stall would otherwise occur, 
so it is not needed.

Stalls are reflected in the STAT register by the Stalled status flag, which indicates the 
current SPI status. The transmitter will be stalled until data is read from the receive FIFO. 
Use the RXIGNORE control bit setting to avoid the need to read the received data.

 

Fig 51. Examples of data stalls

7UDQVPLWWHUVWDOO&3+$ )UDPH BGHOD\  3UHBGHOD\  3RVWBGHOD\  FORFNVWDOO

0RGH&32/ 6&.

0RGH&32/ 6&.

0,62

026,

6HFRQGGDWDIUDPH

5HFHLYHUVWDOO&3+$ )UDPH BGHOD\  3UHBGHOD\  3RVWBGHOD\  FORFNVWDOO

0,62

026,

0RGH&32/ 6&.

0RGH&32/ 6&.

6HFRQGGDWDIUDPH

)LUVWGDWDIUDPH

)LUVWGDWDIUDPH

5HFHLYHUVWDOO&3+$ )UDPH BGHOD\  3UHBGHOD\  3RVWBGHOD\  FORFNVWDOO

0RGH&32/ 6&.

0RGH&32/ 6&.

0,62

026,

6HFRQGGDWDIUDPH

)LUVWGDWDIUDPH

06%

06%

/6%

06%

06%

/6%

06%

06%

/6%

/6%

06%

06%

/6%

/6%

/6%

/6%

06%

06%

/6%

/6%

06%

06%

/6%

/6%

Summary of Contents for LPC5410x
















































































































































































































































































































































































































































































Reviews:

No comments