manualshive.com logo in svg

NXP Semiconductors LPC5410x, User Manual, Page: 240 / 463

Share
Download
NXP Semiconductors LPC5410x User Manual Download Page 240

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

241 of 464

NXP Semiconductors

UM10850

Chapter 17: LPC5410x Multi-Rate Timer (MRT)

17.6.3 Control register (CTRL)

The control register configures the mode for each MRT and enables the interrupt.

 

17.6.4 Status register (STAT)

This register indicates the status of each MRT.

 

Table 283. Control register (CTRL[0:3], address 0x4007 4008 (CTRL0) to 0x4007 4038 

(CTRL3)) bit description

Bit

Symbol

Value

Description

Reset value

0

INTEN

Enable the TIMERn interrupt.

0

0

Disabled. TIMERn interrupt is disabled.

1

Enabled. TIMERn interrupt is enabled.

2:1

MODE

Selects timer mode.

0

0x0

Repeat interrupt mode.

0x1

One-shot interrupt mode.

0x2

One-shot stall mode.

0x3

Reserved.

31:3

-

Reserved.

0

Table 284. Status register (STAT[0:3], address 0x4007 400C (STAT0) to 0x4007 403C (STAT3)) bit description

Bit

Symbol

Value

Description

Reset 
value

0

INTFLAG

Monitors the interrupt flag.

0

0

No pending interrupt. Writing a zero is equivalent to no operation.

1

Pending interrupt. The interrupt is pending because TIMERn has reached the end of the 
time interval. If the INTEN bit in the CONTROLn is also set to 1, the interrupt for timer 
channel n and the global interrupt are raised. 

Writing a 1 to this bit clears the interrupt request. 

1

RUN

Indicates the state of TIMERn. This bit is read-only.

0

0

Idle state. TIMERn is stopped.

1

Running. TIMERn is running.

2

INUSE

Channel In Use flag. Operating details depend on the MULTITASK bit in the MODCFG 
register, and affects the use of IDLE_CH. See 

Section 17.6.6 “Idle channel register 

(IDLE_CH)”

 for details of the two operating modes.

0

0

This channel 

is not

 in use.

1

This channel 

is

 in use.

31:2

-

Reserved.

0

Summary of Contents for LPC5410x
















































































































































































































































































































































































































































































Reviews:

No comments