manualshive.com logo in svg

NXP Semiconductors LPC5410x, User Manual, Page: 142 / 463

Share
Download
NXP Semiconductors LPC5410x User Manual Download Page 142

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

143 of 464

 

12.1 How to read this chapter

The DMA controller is available on all parts.

12.2 Features

•

22 channels, 21 of which are connected to peripheral DMA requests. These come 
from the USART, SPI, and I

2

C peripherals. One spare channels has no DMA request 

connected, and can be used for functions such as memory-to-memory moves. 

•

DMA operations can be triggered by on- or off-chip events. Each DMA channel can 
select one trigger input from 20 sources. Trigger sources include ADC interrupts, 
Timer interrupts, pin interrupts, and the SCT DMA request lines.

•

Priority is user selectable for each channel (up to eight priority levels).

•

Continuous priority arbitration.

•

Address cache with four entries (each entry is a pair of addresses).

•

Efficient use of data bus.

•

Supports single transfers up to 1,024 words. 

•

Address increment options allow packing and/or unpacking data.

12.3 Basic configuration

Configure the DMA as follows:
Use the AHBCLKCTRL0 register (

Table 51

) to enable the clock to the DMA registers 

interface.

•

Clear the DMA peripheral reset using the PRESETCTRL0 register (

Table 35

).

•

The DMA interrupt is connected to slot #3 in the NVIC.

•

Each DMA channel has one DMA request line associated and can also select one of 
20 input triggers through the input mux registers DMA_ITRIG_INMUX[0:21].

•

Trigger outputs are connected to DMA_INMUX_INMUX[0:3] as inputs to DMA 
triggers.

For details on the trigger input and output multiplexing, see 

Section 8.5.2 “DMA trigger 

input multiplexing”

.

UM10850

Chapter 12: LPC5410x DMA controller

Rev. 2.4 — 13 September 2016

User manual

Summary of Contents for LPC5410x
















































































































































































































































































































































































































































































Reviews:

No comments