manualshive.com logo in svg

NXP Semiconductors LPC5410x, User Manual, Page: 366 / 463

Share
Download
NXP Semiconductors LPC5410x User Manual Download Page 366

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

367 of 464

NXP Semiconductors

UM10850

Chapter 25: LPC5410x 12-bit ADC controller (ADC0)

11

BYPASSCAL

Bypass Calibration. This bit may be set to avoid the need to calibrate if offset error is 
not a concern in the application.

0

0

Calibrate. The stored calibration value will be applied to the ADC during conversions 
to compensated for offset error. A calibration cycle must be performed each time the 
chip is powered-up. Re-calibration may be warranted periodically - especially if 
operating conditions have changed.

1

Bypass calibration. Calibration is not utilized. Less time is required when enabling the 
ADC - particularly following chip power-up. Attempts to launch a calibration cycle are 
blocked when this bit is set.

14:12 TSAMP

Sample Time. The default sampling period (TSAMP = “000”) at the start of each 
conversion is 2.5 ADC clock periods. Depending on a variety of factors, including 
operating conditions and the output impedance of the analog source, longer sampling 
times may be required. See 

Section 25.7.10

.

The TSAMP field specifies the number of additional ADC clock cycles, from zero to 
seven, by which the sample period will be extended. The total conversion time will 
increase by the same number of clocks.

000 - The sample period will be the default 2.5 ADC clocks. A complete conversion 
with 12-bits of accuracy will require 15 clocks.

001- The sample period will be extended by one ADC clock to a total of 3.5 clock 
periods. A complete 12-bit conversion will require 16 clocks.

010 - The sample period will be extended by two clocks to 4.5 ADC clock cycles. A 
complete 12-bit conversion will require 17 ADC clocks.

:

111 - The sample period will be extended by seven clocks to 9.5 ADC clock cycles. A 
complete 12-bit conversion will require 22 ADC clocks.

0

31:15

Reserved. Read value is undefined, only zero should be written.

0

Table 416. ADC Control Register (CTRL, address offset 0x0) bit description

Bit

Symbol

Value Description

Reset 
value

Summary of Contents for LPC5410x
















































































































































































































































































































































































































































































Reviews:

No comments