manualshive.com logo in svg

NXP Semiconductors LPC5410x, User Manual, Page: 208 / 463

Share
Download
NXP Semiconductors LPC5410x User Manual Download Page 208

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

209 of 464

NXP Semiconductors

UM10850

Chapter 14: LPC5410x Standard counter/timers (CT32B0/1/2/3/4)

14.7.1 Interrupt Register 

The Interrupt Register consists of 4 bits for the match interrupts and 4 bits for the capture 
interrupts. If an interrupt is generated then the corresponding bit in the IR will be high. 
Otherwise, the bit will be low. Writing a logic one to the corresponding IR bit will reset the 
interrupt. Writing a zero has no effect. The act of clearing an interrupt for a timer match 
also clears any corresponding DMA request. Writing a zero has no effect.

 

 

14.7.2 Timer Control Register 

The Timer Control Register (TCR) is used to control the operation of the Timer/Counter.

 

 

Table 242. Address map IR register

Peripheral

Base address 

Offset

Increment

Dimension

CT32B0

0x400B 4000

0x000

-

1

CT32B1

0x400B 8000

0x000

-

1

CT32B2

0x4000 4000

0x000

-

1

CT32B3

0x4000 8000

0x000

-

1

CT32B4

0x4000 C000

0x000

-

1

Table 243. Interrupt Register (IR, address offset 0x000) bit description

Bit

Symbol

Description

Reset Value

0

MR0INT

Interrupt flag for match channel 0.

0

1

MR1INT

Interrupt flag for match channel 1.

0

2

MR2INT

Interrupt flag for match channel 2.

0

3

MR3INT

Interrupt flag for match channel 3.

0

4

CR0INT

Interrupt flag for capture channel 0 event.

0

5

CR1INT

Interrupt flag for capture channel 1 event.

0

6

CR2INT

Interrupt flag for capture channel 2 event.

0

7

CR3INT

Interrupt flag for capture channel 3 event.

0

31:6

-

Reserved. Read value is undefined, only zero should be written.

-

Table 244. Address map TCR register

Peripheral

Base address 

Offset

Increment

Dimension

CT32B0

0x400B 4000

0x004

-

1

CT32B1

0x400B 8000

0x004

-

1

CT32B2

0x4000 4000

0x004

-

1

CT32B3

0x4000 8000

0x004

-

1

CT32B4

0x4000 C000

0x004

-

1

Table 245. Timer Control Register (TCR, address offset 0x004) bit description

Bit

Symbol

Value

Description

Reset 

value

0

CEN

Counter enable. 

0

0

Disabled.The counters are disabled.

1

Enabled. The Timer Counter and Prescale Counter are 
enabled. 

Summary of Contents for LPC5410x
















































































































































































































































































































































































































































































Reviews:

No comments