Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 69

Page: 69 / 109

- A22 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

PL-22SEL

#1006

#1009

PL-22SEL

#106

#104

#109×2

EDB0011

Apply to the overall

pattern surface.

Apply the adhesive (PL-22SEL) to the pattern surfaces of the focus encoder FPC (#1009) and zoom
encoder FPC (#1006).

•

Apply to the overall

pattern surface.

Set the lens to WIDE position, and attach the zoom brush (#104) and plate (#106).
Tighte the two screws (#109).

•
•

Place the rounded tip part

of the brush on the above

position.

Zoom brush

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands